JDS28CKC General Electric Range - Instructions

took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mounting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.

Exactly as you descibe and after disconnecting the two wires from the contacts on the element and taping the two wires to the oven wall so they do not fall back into the hole from where they came was extremly helpful. Also was an opportune time to clean the oven properly prior to installing the new element.

Thanks

Red Light Off

Went to You Tube, found the appropriate segment. "Wa La" the problem was solved. Burner is working the way it is supposed to.

I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.

First replaced the 8" burner element-still did not work.
second: replaced the TERMINAL BLOCK KIT still did not work.
third : finally replaced switch: very easly-make sure you do not take off any of the wires on the back of the switch-take new switch and replace each wire on the same location than remove the old switch and replaced wired new on with the two screws.

Removed the burner coil.
Unscrewed the terminal block.
Pulled out the stove and disconnected the 220 Volt service at the plug.
Removed the back panel at the control knobs.
Detached the wiring to the control knob and pulled thru the back panel.
Wiring mostly visable to the front 8 inch burner.
Replaced wiring and mounted new terminal block.
Tested the burner for a few seconds.
Replaced back panel and set stove in place.
Saved $150 dollar service call.

1. Shut off power at breaker.
2. lift and prop up burner panel (top of stove)
3. removed three screws along top edge.
4. remove oven door (lifts off hinges easy)
5. remove 4 screws along upper oven opening
6. remove 2 screws up under front panel and pull out upper panel enough to access back of switches.
7. unplug wires (5) one at a time and plug onto new switch.
8. remove the two screws from front holding switch in place and remove old switch.
9. install the two screws attaching new switcj.
10 replace all screws in reverse order.
11. Re-install door.
12 close breaker
easy job any one with any mechanical no-how can do.

followed video exactly

easy to do.

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

This appeared to be an easy fix, but turned out to be more involved than I planned. The hard part was pulling the range/microwave oven assembly away from the wall so I could remove the back panel and see how the new terminal block wires connected up to the switch/knob that operates the burner. Extracting the whole range unit required me to use a floor jack to raise the leveling feet of the range above the edge of my floor tile so I could slide the unit out. Once away from the wall, I used a nut driver to remove the back panels. Next surprise was the new terminal block wire connectors were not the same type as the old block's connectors (flat vs. male pin-type). Rather than let the scope of this job creep to include a whole new connector rig, I opted to splice the new terminal block wires onto the existing wires that led up to the control knob. I used professional splices and a crimping tool to secure the wires. After checking the new installation was sound and operational, I slid the whole range back into place. Attaching the new terminal block to the range top was a piece of cake, but getting the damn oven out into open space where I could work on it was bear. But, hey, I learned a few things, one of which is that when a homeowner decides to retile their kitchen, make sure you run the new tiles all the way under the range and not just up to the front edge of the oven. I can see why this was done - to avoid having to remove the oven during the retiling - but it creates an obstacle for whenever the oven needs to be pulled away from its location. The last tool I imagined I would need for this repair was a car jack. The Parts Select part worked fine.