JK14*R3 General Electric Range - Instructions

Very simple 4 screws/nuts ...off on...done.
Best part was that I ordered the part regular shipping on a Sunday. Monday was a holiday...the part was at my doorstep at 8AM Tuesday morning. Wow that's service.

Unscrewed the two screws holding the element to the back oven wall, then I was able to pull the element out. I then unsrewed the two screws holding the two wires to the element. Installation was the reverse. Pretty simple job.

Unscrewed the broken element from the back of the inside of the oven, then unscrewed the connected wires from the element and did the reverse with the new element. Viola.

Before touching anything, however, I made sure the oven was in the off position and also went to the house circuit breaker box and flipped OFF the appropriate circuit breaker(s). There were two - one for the element and another for the rest of the controls.

When everything was in place, I turned the power back on and turned on the oven and was cooking again. We had Prime Rib for Easter.

The replacement was straightforward, six screws. Instructions were provided with the part along with the necessary screws to fit the new element terminals.
Open the breaker, verify power is off, remove the old burner. Install the new burner and mounting bracket. Restore power and test. In and out in less then thirty minutes.

I (a woman) unplugged the stove, took out the screws, and unhooked the baking element. I then replaced the old screws with the newer ones, and made sure everything was nice and tight. I was a little nervous at first but everything turned out okay. I plugged the stove back up & the baking element was a bright orange and it works better than ever. The whole process took about 15-20 minutes.

You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.

Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

The longest step in the fix was the walk downstairs to turn off the breaker.
1 nut driver to remove the element from the oven. 1 screwdriver to disconnect. Just as simple to re-install.

If you have this oven I seriously recommend the $30 expense to replace the element before it fails. It honestly went out with a white hot welder's torch sort of short circuit that could have burned my house down.

A friend gave me your website. I looked up the model (is over 30 years old & obsolete!), but you listed a similar model. Part fit perfect, works great, heats to set temp quickly. Your do-it-yourself page was a big help...thanks! Replacement went quick and easy after I saw what needed to be done.

The bottom heating element burned out. Ordered the right part and my husband fixed the heating element. This saved a lot of money.Thanks, RM from South Carolina

so easy it doesn't need an explanation. Just remember to throw the breaker switch before beginning!