JGB918SELS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ERNEST from MANCHESTER, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIE from SYLMAR, CA
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Burner knob appears to be no longer available.
I have requested this part with the original p/n WB03K10303 and
p/n AP396896. Each times I received a different part than part I ordered. Has this parts been revised? The shaft of the knob is to to small
to to slide over burner controller stem.
p/n AP396896. Each times I received a different part than part I ordered. Has this parts been revised? The shaft of the knob is to to small
to to slide over burner controller stem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- P from FULLERTON, CA
- Parts Used:
- WB13X26360
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Part does not look like the part that needs to be replaced
I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from HACIENDA HTS, CA
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken burner knobs
Just plowing in one by one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from LAURELTON, NY
- Parts Used:
- WB03X43926
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken stem on knobju
Just remove the other knobs and replace with new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Constance from Spokane, WA
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were plastic and broke
took old knobs off and put new ones on - they fit perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Mount Pleasant, UT
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Burner Knobs melted when did oven self clean
Pulled off melted knobs and pushed on new knobs. Easy, easy, easy and the knobs appear to be a better qualify than the original knobs. Was very pleased with the parts from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Lorton, VA
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob surface bubbled up.
I simply pulled knobs off and pushed new ones on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Delafield, WI
- Parts Used:
- WB03X43926
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
wantyed to upgrade the look of a white stove with stainless steel accents
simply switched out the white plastic knobs for the stainless steel knobs
Was this instruction helpful to you?
Thank you for voting!