1J4021M4 General Electric Range - Instructions

Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding element in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks

Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires into insulation and put back on shield.

Replaced lower element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.

First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!

First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service

First , for safety, I flipped breakers to kitchen applicances to cut off the power. Removed the 2 screws that held the old element in place. Pulled it out a couple of inches and disconnected the 2 wires attached to the prongs of the element. Reattached them to the new element, pushed it back in and replaced the screws. Turn power back on and voila! ... was ready to bake again! All this is a matter of 15 mins!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, put the new one in and reversed the procedure. Also delivery was great, I ordered the part and received it the next morning. I highly recommend your service.

First I took out the oven racks removed two screws then I pulled it out a couple of inches to expose the wires and removed the screw. Put the new element in place and replaced the two screws put the wires back and replaced the two screws that hold the element in place.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.

My husband did the repair in about 15 minutes. It was apparently self explanatory and required no directions. Take the old one out and replace it the same way it came out. And viola!!, the oven works like new - all for about $33. Thanks

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above

I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.

First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.

I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)

That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.