JMP28BCW General Electric Range - Instructions

Watched video,and used it as guideline.Biggest problem was removing tape from old wires.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.

With a nut driver removed the four heating element sockets (four small sheet metal screws) and the seventeen sheet metal screws that secured the burn box, removed the sheet metal box and inserted the new one. Not all the holes lined up at first for the screws, but starting in front with the four that did fit, the sheet metal gradually lined itself up with all the other holes for a perfect fit.

Pulled out old with pliers. Twisted new clips in per instructions.

unplugged burners replaced drip bowls plugged in burners

replaced

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pushed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe

took the old ones out and put the new ones in their slots. No issues

Not really a repair. But would like to say, I like the price and shipping was super fast. Thanks.

I thought because the broiler was off that I could remove the element with not problem. As I was pulling the element out, it sparked, melting something in the back I couldn't see at the time. I immediately went to the breaker box and turned the power to the oven off. After I found the website online I was very gratified to see how easy it was to identify the element I needed and order it. I removed the old element. One of the wires from the element slipped through the hole in the back of the oven. To get at it I had to unscrew the four screws around the outside edge of the oven and pull the whole oven out. I had a table handy that I pulled up next to the oven and set it on without disconnecting the main wiring. After getting the oven out I removed the six or so screws on the coverplate and easily found the loose wire. I pushed the wire back through the hole in the back of the oven and made sure it would not fall back into the hole. I put the back plate on with all its screws; pushed the oven back into its hole and screwed the four screws in around the edge that hold the oven in. Then I attatched the broiler element to the spade connectors and screwed it back in place. I turned the breaker switch back on and tested it. It works.

I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.

Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.