JBP61DA2WH General Electric Range - Instructions

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

It took longer to get the new element out of the box than it did to install it. I removed the two screws with a 1/4" nutdriver, pulled the element out roughly three inches, unplugged the connectors and discarded the old element. I did the reverse to install the new element.

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

Removed two screws, pulled old element forward 2 inches, removed two wires. Pulled old element out of oven. Put new element in oven, attached two wires, pushed element all the way in, put two screws in and tightened them. Turned oven on to test new element. Element worked. Project completed.

I took a chance and guessed that the problem was the element, as opposed to a thermostat or other part that may have failed. (Oven was made in the 70's) I entered the data for this old oven on the PartSelect.com website and it came up with a part for me to order. When I received the replacement element, I noticed that it was not "exactly" the same shape as the old part, but the dimensions were correct and it fit into the space on the bottom of the oven without any problems. The dimensions of the connectors were pretty close to exactly the same as the old element, and the screw holes in the mounting plate lined up perfectly with the corresponding threaded holes in the back wall of the oven - it took me less than 15 minutes to install the part and the oven appears to be working perfectly again.

Unplug appliance. Unscrew bolts that hold heating element in place. There will be wires that need to be carefully detached from the heads. Take heating element out. Install new one, reattaching wires and bolts in that order. It might be nice to clean the oven a bit while you're in there, as smelling something burning right after a repair job can be a bit unsettling! Ha. But it works great, and the fix is incredibly easy. So glad we didn't call a repairman.

Shut off power to the range in breaker box used a .025 inch socket to remove two mounting screws pulled forward slowly to disconnect the two wires.Checked for nicks or cracks in wire installed new element restored power done .

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

I unplugged th oven, for my safety. Removed 2 small bolt head screws, unplugged 2 wire connecters similar to car speakers connecters. Removed the element. Then took a few minutes to clean bottom of oven. It is so much easier with out the element. I plugged the wires onto new element, then i put the 2 small screws back in. Plugged in oven, pushed it back in place and turned on oven. It has been great! I think old element was unevenly heating. Baking has been noticable better. Thank you partselect.com. a very satisfied New England customer

Remove center cover on back of stove exposing wiring. Unplug stove from 220v outlet. Unplug wires from old element.From inside stove, Remove 4,quarter inch screws holding back panel inside oven in place. Remove back panel from inside oven. Will be able to see the brackett on element and 2 screws holding the element/brackett in place, remove those 2 screws and remove old element. Reverse process to install new element.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

The only problem was m short arm and no good flash lights around