J349*02 General Electric Range - Instructions

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

I shut down the electric to the oven at the circuit breaker. Then i loosened the mounting screws and pulled the element from the back wall of oven. Then i disconnected the two leads to the element with a phillips screwdriver and removed element. Installation was done in reverse order.

The replacement was straightforward, six screws. Instructions were provided with the part along with the necessary screws to fit the new element terminals.
Open the breaker, verify power is off, remove the old burner. Install the new burner and mounting bracket. Restore power and test. In and out in less then thirty minutes.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Easy has falling off a log!!!!!!!!!!!!

less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...

Removed 4 screws and removed the old element and replaced in the reverse order.

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.

removed old element rewired new element,turned back on power

Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.

These two repairs were straight forward and the repair does not need elaboration. The amazing aspect of this repair was that I ordered my parts and received them on the second business day without any additional charges. That was really fast ! Thanks Partselect.

i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.