1J4081M2 General Electric Range - Instructions

First I turned off the breaker to the stove in the breaker box and then removed the two small screws that hold the element in place. I then carefully pulled the element out about 3 inches and using a 1/4 inch socket, I unscrewed the screws that held the wire on the bake element. There were two wires held in place with 2 small screws. I made sure that when I unhooked the wires they did not pull back into the back wall of the stove. I then removed the old element and put the new one in its place, hooked the two wires back up, pushed it back in place and secured it to the back of the wall of the stove with the other two screws. I then turned the power back on and presto, it worked perfectly. Like new again.
Thanks for everything.

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

I removed both screws to remove lower element, and measured it prior to ordering the replacement.
Then in a few days it arrived, and I installed it. The new element had small bolts rather than screws the original used to attach both wires. A flashlight was necessary in locating an keeping an eye on the wire ends, to keep them from being pulled inside the back cover, as the bolts were attached.

Element was in two pieces so it was obviously dead. I disconnected the stove from the power, I undid the two screws at the back of the oven and gently pulled the element out. There was enough slack to reach and pull the connectors apart. Done. I ordered the part from "PartSelect" and it arrived the next day. Unfortunately I ordered the element with "Screw" convectors as opposed to "push on" connectors. I bought a couple of connectors and cut off the original connectors from the wires in the oven and replaced them making absolutely sure they were well and truly tight. Two screws cam with the element from "PartsSelect (Thankfully). Connected the wires and screwed it back into place. Stood clear, plugged it in and turned it on to max. Worked just fine, Thanks

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks

Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!

I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.

Turned the power off. Loosened two screws to take the element out. Loosened two more srews to disconnect the element itself from the power. This job was easy squeezy. Within 15 minutes flat I was back on the couch watching old Seinfeld reruns. Two thumbs up for the peeps at Part Select.

Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!

Turned off breaker for oven, removed baking (lower) element, searched website to match up size, shape, and connector-type of replacement part. Placed order and received two days later. Mounted new part in 10 minutes, turned on breaker, and immediately baked fries for children. No problem. Much cheaper and easier than replacing entire built-in oven.

Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!

pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.

got new part delivered two days after ordering. I turned off breaker, used a 1/4" wrench to remove the fasteners holding the heating element to the back inside wall of the oven. used screw drivers (one Phillips and one flathead) to remove the screws holding the heating element to the wires. ensure you pull the wires slight out (easily) to ensure they don't pull back into the oven wall. unplug the element from the wires, install new element in reverse fashion and voila, done.