1J4081M2 General Electric Range - Instructions

Repair was easy.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.

I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.

The part came next day, which was a surprise.
Removal and Installation was 4 screws.
I have become a DIY hero.

Only downside was going out for dinner every night ended.
This site is now a Favorite.

I unscrewed the old burner from the stove, took off the three wire to the heating element marking down where each colored wire went, taped off the exposed wires, ordered the new burner, and waited for it to arrive. When it got here, I installed it, and believe it or not, the new burner works just fine!. End of exciting repair story.

Took the old part off and marked the wiring for easy replacing and looked all over town and no part to match, so I went to the Internet and put in 8" burner and luckily found your website. The part was perfect and saved me alot of time doing more research for the part. Thank you for the quick shipment and good correspondence.

I will definitely use you again for parts and tell my friends about your website too.

Took the broken heating element out of oven. Replaced with new one; which was easy to do.

Turned on oven. It started heating immediately

diagnosed repair by installing heating element from lower oven into upper oven, and it worked. Ordered proper replacement part and installed using tools above. No problem besides the tight space.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires

removed it, ordered it and it only took 15 minutes to replace it.

I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.

Very quick delivery, within 3 days.

I removed the two screws that hold the element to the back of the oven. Pulling the element out of the back, I removed the screws which connect the element to the electrical wiring. I placed the new element into position and reconnected the wiring. I made sure that the wiring and connectors were insulated with shrink wrap plastic, then pushed the new element into place. Connecting the two screws to the back of the oven completed the job. Toughest part, kneeling on my knees -- the part supplied fit like a glove and it works wonderfully well. Hint: measure the connectors to the wiring so that you order the correct length! (I didn't and had to reorder, but I am very happy with PartSelect.)

First of all the part came super fast with standard delivery. We threw the circuit switch to the oven. We used a nut driver to remove the nuts holding the element in place and then gently pulled it out of the hole so we could see the terminals. Using a screwdriver we loosened the screws that hold the terminals to the power lines. We put the old element aside and laid the new element on the floor of the oven. Using a screwdriver and the original screws we attached the terminals of the new element to the power lines. Using a screwdriver and the new screws provided we attached the bracket to the back of the oven. Turned on the power; used the oven. Works perfectly.

Super easy, 1 2 3 steps and your done. Make sure to turn power off, remove two screws off of back plate. Remove two screws on wire connectors. Throw old element away and connect both wires to new element and screw back into place. Turn power back on and start cooking.

very easy--cut power supply 2 screws then 2 more on element quick and easy

First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!

Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires into insulation and put back on shield.

Replaced lower element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.