J330*01 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.

First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!

Cut the power off to the range, unscrewed the burner from range and pulled off the element and unscrewed the two screws

First , for safety, I flipped breakers to kitchen applicances to cut off the power. Removed the 2 screws that held the old element in place. Pulled it out a couple of inches and disconnected the 2 wires attached to the prongs of the element. Reattached them to the new element, pushed it back in and replaced the screws. Turn power back on and voila! ... was ready to bake again! All this is a matter of 15 mins!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, put the new one in and reversed the procedure. Also delivery was great, I ordered the part and received it the next morning. I highly recommend your service.

My husband did the repair in about 15 minutes. It was apparently self explanatory and required no directions. Take the old one out and replace it the same way it came out. And viola!!, the oven works like new - all for about $33. Thanks

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above

First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

i removed the two screws that hold the element in place. i then pulled the element out and disconnected the two wires. then i connected the two wires and screwed the element back in place and now it works like new.

first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks

The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.

Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank