J355101 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Virginia from Carmel, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broiler element was broken
Asked a local repairman to fix it. I saved money(saved $20.00) by ordering the broiler element from GE part select via customer service agent. The agent was informative and helpful. The part arrived the next day even with regular shipping cost. Impressed with the GE part select. Will use the company again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVEN from HERNDON, VA
- Parts Used:
- WB2X3138
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Oven door gasket hard, noot sealing
I thought it would be a simple matter of removing the inside glass (4 screws) and replacing the gasket, but it turns out that on this model I had to start on the outside, remove the drawer, then remove the front door cover, then undo a screw which held the inside two-tier glass in place, THEN I could remove the four screws and the interior panel which holds the gasket in place. THIS IS A TWO PERSON JOB unless you choose to use masking tape to hold the exterior door cover in place while removing/replacing the many screws which hold it on. WHILE REPLACING THE INTERIOR COVER WHICH HOLDS THE GASKET IN PLACE, YOU MUST PERIODICALLY STRETCH IT HERE AND THERE TO GET THE "SNAKE" TO EXTEND THE ENTIRE WAY AND TO SEAL TIGHTLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meagan from Weston, FL
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil Element Stopped Heating
The broil element was easy to replace. Start by either unplugging the unit from the wall or turning the circuit breaker off. I started by removing the two screws that hold it in the back. There was a support bar attached to the top with two screws also. After removing all screws, gently pull the element forward exposing the two wires. Make note of which wire goes to which terminal. I also clipped a clothes pin to each wire to prevent them from falling back through the hole. Disconnect the two wires and reconnect to the new element. Reattach all screws and you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Temecula, CA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven not getting hot to preset temp
First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cheryn from lynchburg, VA
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
replace burner, drip bowl and ring
This was a second hand stove we have had for about 3-yrs. I noticed immediatley that the drip bowls and rings were not OEM parts & the bottom of the burners had actually been bent to fit the rings. I was very glad to find this website with a detailed diagram of the stove and parts. I intend to replace all the burners, drip bowl & rings, and then start replacing other parts as needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond ` from Houston, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broiler electrical heating element burn-out.
Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Ellettsville, IN
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element burned out
From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ELAINE from MURFREESBORO, TN
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dirty drip pans
My stove top is 35 yr old. & Lowes did not have drip pans that fit. these worked great & easier than cleaning the old ones. They just popped right in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from york, ME
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
support uder buner broke
The repair was almost to easy. It makes me wonder how many times in the future I will be willing to now attempt a repair instead of waiting and paying much more to have someone else do it. I thank you for the easy to understand video directions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sarah from San Andreas, CA
- Parts Used:
- WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original trim ring did not fit
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from richland, WA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
dirty drip pans and rings in new house i bought
could not find the proper pans and rings in any diy stores, as stove is so old. went on this site and there they were!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from San Jose, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed new Drip Pans
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alvin from jamaica, NY
- Parts Used:
- WB32X10013, WB31X5014, WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The burner stoped working
unskewed the screw. Very basic
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valerie from Ogden, UT
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Condo Had Very Old Drop In. Threw Away Drip Pans And Rings
Placed new ones on range. Exactly what I would do to wash them.
Was this instruction helpful to you?
Thank you for voting!