JKP36G009 General Electric Range - Instructions

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one

After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.

Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!

husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

Removed the coverplate screws, slid the element outward, and removed the wire connecting screws. Positioned the new element to reconnect the wires, and discovered this isn't easy to see with trifocals. Succeeded after several failed attempts. Slid the new element into position, and reattached the cover plate.

I shut down the electric to the oven at the circuit breaker. Then i loosened the mounting screws and pulled the element from the back wall of oven. Then i disconnected the two leads to the element with a phillips screwdriver and removed element. Installation was done in reverse order.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.

Removed the two screws holding the mount and then reattached the two wires to the element.

Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!

P.S. Shipping was very fast.

First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven

replaced with a new part . Thanks for all your assistance in getting the correct part

remove two screws from back of oven holding element to back of oven. Pull out gently, remove two screws holding wire connections(power wires) throw away old element. Place new element into oven. Reconnect element to power wires using screws. Push element back into back of oven. Replace screws holding element in place. Turn oven on to check for proper connections.

First turned power off for oven circuit at the breaker box then removed two screws that hold element in place. Pulled element out, tested for current, then removed two screws holding wires to element. Took old element from oven and inserted new element. Reattached wires with screws provided, and pushed element into opening. Replaced two screws securing element to back wall of oven. Turned the circuit breaker back on then checked to ensure the oven was working.

1. Turned the electricity off at the fuse box.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.