JGBP33CEH4CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from Redondo Beach, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from Riverside, RI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hot Spot On Burner
Replaced old burner element with new, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FELIX from DELTONA, FL
- Parts Used:
- WB34K10016, WB34K10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pan Replacement
It was a snap. Lifted all 4 burner grates, pulled old drip pans out, installed the new ones. Perfect fit. My mother is happy-happy. thanks Parts Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Millington, MI
- Parts Used:
- WB28K10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Threads on elbow stripped out
Part was purchased to replace damaged elbow. During the conversion to LP gas the elbow threads were stripped from over tightening the collar nut. To accomplish the replacement: 1. remove 2 sheet metal screws holding protective shroud in place. 2. disassemble the compression fitting CAUTION DO NOT OVERTIGHTEN 3. loosen elbow collar nut if necessary and remove elbow. 4. reassemble starting with the compression fitting. 5. connect the elbow to the broiler burner with the collar nut 6. tighten all the way down turning nut cw for LP conversion CAUTION DO NOT OVER TIGHTEN 7. with broiler on adjust flame and check for leaks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Perkiomenville, PA
- Parts Used:
- WB34K10016, WB34K10015, WB29K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace the drip pans, burner caps and grates due to old age.
After one week, the enamel on the drip pans and 1 of the burner caps were starting to wear away. They gave me a refund,including shipping and sent me replacements. They are a very reputable company.I will buy items from them again.
Was this instruction helpful to you?
Thank you for voting!