JBP95TF1WW General Electric Range - Instructions

Replaced it

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Installed new guides with a nut driver without any problems.

Turned off the power at the breaker. Then I lifted the cooktop by pressing up from the bottom, while my wife slid two boards over the recess. I lowered the cooktop onto the boards, removed 12 screws around the perimeter of the case and carefully lifted the glass top and placed it on a towel on the DR table. (remove the control knobs first) removed the wires leading to the infinite control, marking which color when where, removed the two screws holding the infinite control, and replaced the old with the new. Reattached the wires, replaced the cooktop, replaced the screws, held it up while my wife removed the boards and then carefully lowered the cooktop into the recess. Attached the knobs, flipped the breaker back on and turned control to hi. It worked!

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

plug in thermistor when needed

Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.

A cleaning spray was allowed to caused a short circuit of the infinite control switch. Here is the sequence of a very easy way to repair it: Turn off the power to the unit. Take the bottom metal cover off. You should be able to find the one that was burnt out (my was the bigger surface burner switch). Take photos of how each colored wire are connected ( I used my cell phone). Review the photos!! You will see that the switch has two clamps holding the metal cover to the plastic casing on the sides. Using a narrow screw driver, pop loose the plastic casing from the metal clamps. This way you don't have to take the unit totally apart. The metal casing should be fine. Clean it well, making sure it is dry. Take the new switch and also take the plastic casing from the metal top cover. Replace the metal pin and the plastic casing only. Make sure you line it up the same way with the little blue box in the same orientation. You may not have enough room for your hand and your view. By feel, you should be able to place it there and pop it in. Check the taken photos and connect the wires following the same diagram. Replace back the metal cover. Turn the power on. Enjoy dinner!!! Michael.

Simply remove the large screws from the inside of the door and the smaller screws that hold the handle on. We used a "star" tip screwdriver bit (it might be called a torx head?). Keep the smaller screws separate as they are slightly different in length. Remove the handle. Slide the vent piece off. Reassemble with the new trim piece. The stove looks as good as new. It took less than 15 minutes and we avoided the $79 repair call. One has to wonder why manufacturers use plastic parts in an area that gets so hot that it scorches when the self cleaning cycle is used?

Easy to install replacement parts using the screws provided.