RB525BHW General Electric Range - Instructions

First and foremost I read each of the blogs from your site from other people who have repaired this part. It was great.
First I unplugged the stove. Removed the back plate of the stove by unscrewing 6 screws. Removed the heating element & drip pan. I lifted up the stove top to examine the receptable, and removed the receptable held in place by a single screw using the nutdriver.
Once it was removed, I cut the wires attached to the receptacle with pliers. I screwed on the new receptacle, and taped the new wires to the old ones which led back to the back panel where they were attached to the switch.

By doing so, I was able to easily lead the new wires to the back side of the stove panel. I removed each old terminal wire and replaced it with the new one. (I had read in a previous blog that the polarity of the new wires didn't matter). I replaced the drip pan, and heating element, turned the switch and everything was working just great! I replaced the back panel, and that was it!
As you probably can guess I have never attempted to repair any type of appliance...ever! But your website and the people who shared their stories empowered me to do the job. Thanks so much!

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

pull out, push in

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.

The longest part of the job was finding my misplaced nut driver!!Note:A small socket set will do.Unplug stove from outlet,remove rear cover panel,lift stove top up to access terminal. remove the one screw that holds the terminal and slide off the two wire clips that hold the wires up out of the way.next clip off the old terminal leaving the old wires so you can tape the new wires on just to pull them through the hole.Once you have the new wires pulled up to the heat control unplug old and replace with the new,tighten the screw on the new terminal and don't forget to slide on the wire clips

First I removed the burners and pulled the stove out to get the back cover off. Removed the back cover after main power was shut off. Removed old burner terminal blocks and replaced with new ones. Replaced back cover and pushed stove back into place. Turned on main power to stove checked burners and they worked. DO NOT REPLACE OR DO ANY ELECTRICAL WORK ON ANY MAJOR APPLIANCE WITH OUT FIRST TURNING OFF THE MAIN POWER SOURCE.

Received complete burner receptacle. Decided to take off stove back to plug in directly to burner control.
Turn on stove on low. No heat. Bad coil element. Checked for power at coil element. Switched another burner. It heated immediaetly. Have to order or find a burner element

Since the unit is a drop-in range I had to remove the heat shield/drip plate to thread the wires from the control button to the receptable. The replacement part wires were to short to make the connection so I have to use some of the wiring from the old receptable to make the connection. That is the reason for using the wire cutter and connecters.

Pull out the range. Pull out the electric plug. Unfasten the back panel. Raise the range top. Replace the terminal block in exactly the same position as the old one. Put everything back.

This is the third time I have replaced it so it is very easy now. This time I spent a little more time making sure the burner element prongs were just just like the others. Must have been a little loose in the block.

Shut the power off and unscrewed facial hardware ,unplugged terminal and unscrewed hold down bracket and redid everything that I mentioned above. For a rookie it was a piece of cake.

I first unpluged the stove then removed the 6" element then I removed the back panel on the stove located the wires that went to that element unplugged them and removed the block then fished the wires through for new terminal block installed in terminal block bracket then pluged in wires put element in place put back panel back in place plugged stove checkout heat on element good to go 20 min