JCSP38BK2BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Isabel from The Colony, TX
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner bowls were burnt through and nasty looking.
I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherman from OPELOUSAS, LA
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The burner coil had shorted out and actually burnt a hole in my non stick pan and after I replaced that, it would not heat up again. I actually swapped the wires from the back burner, but the small coils use a different watt switch and it would barely boil water with the big coil. So I ordered this
First turn off the breaker, and test with my milti meter. Raise the top panel where the coils are and prop it open high enough to use a screwdriver to open the front panel.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.
Then unscrew the three screws on the inside of the top panel, then open the oven door and you will see 4 screws across the bottom of thefront control board panel and two more on each side of the sides of the panel facing straight up. Unscrew those 6 screws and then pull the front control panel forward and out. You might need something or someone to hold the panel, I just let the wires hold the weight, but not highly recommend. Then pull the switch knob off and behind it there are two little bitty screws that hold the switch in place. Unscrew them and pull the switch out of its place. I put the new switch close to the old one and just used the needle nose pliers to unplug one wire at a time and plug it in on the same place as the old one.
Then screw the itty bitty screws in the front that hold the switch in place and put tbe knob back on. Reposition the front panel back into place abs screw in the 9 screws removed for disassembly. Now would be a good time to clean under the burner panel if you haven’t done so yet ( it gets pretty nasty under there). Then put your burner top back down into place and turn your breaker back on. You can either test with your multi meter or like I did, just put the burner on high and watct the coils glow. Such a beautiful sight. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from bend, OR
- Parts Used:
- WB23T10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
F2 Warning - Oven overheating
I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from HONEA PATH, SC
- Parts Used:
- WB24T10025
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Switch started arcing in the dial range of 2 to 8 in about a year.
Pulled the range out and unplugged it. Removed the back panel. Removed one wire at a time and plugging it in on the new switch. unscrewed the existing switch from the front panel (Two screws). Screwed the new one in, replaced the panel, plugged in the range and tested it. The new switch was a perfect OEM replacement and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Fraser, MI
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
In My Carelessness, I Ruined The Burners On My Stove Using A Really Abrasive Cleaner, And Had To Replace Them With New Ones. My Stove Looks Brand New, And I Feel Better!!
Nothing to it. Took off the old ones and put on the new! Tada - new stove!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from sewell, NJ
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drwer slide under stove broke off.
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Frederick, MD
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Oven Light Assembly damaged
I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.
Jose Figueroa
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Norwalk, CT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement of old parts
Fortunately there was no repair needed, just a replacement of old parts, but I was very pleased with the speed of delivery and the quality of the parts. I'm a happy customer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Tucson, AZ
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip pans on stove top burned black
I got tired of trying to find the right parts in the stores and decided to order them. Finally I have the drip pans that fit my range!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jewel from Nacogdoches, TX
- Parts Used:
- WB25T10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The temperature indicator light on the oven was broken.
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- aiden from philadelphia, PA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
drip pans had become old and burned out
Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SILVIA from Midlothian, TX
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner not work
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from EDENTON, NC
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Defective switch
Replaced element control switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from HOPEWELL, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Just didn't work no pwr to it
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this instruction helpful to you?
Thank you for voting!