J365*01 General Electric Range - Instructions

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

First I turned the power to the stove off at the breaker box. Next I removed the two screws holding the old element in place against the back wall of the oven. I gently pulled the element forward. I wound a couple lengths of spare colored wire around the two electrical wires before disconnecting the retainer screws at their connection points. This insured that the electric wires would not fall back inside and behind the firewall. I then disconnected the screws holding the electrical wires to the broiler element. I removed the element from the oven and discarded it. I then connected the screws through wires and the connecting points of the new element. I removed the spare wires hold the electrical wires. I positioned the broiler element in place and screwed in the retainer screws securing it in place. I turned the breaker switch to the "on" position and tested the new broiler element. It tested fine. Job done in 15 to 20 minutes. An able bodied person could do it in less than 10 I'm sure.

removed timer assy. with wires attached, then mounted new timer in place. Took wires off old timer and installed on new timer one at a time. Worked like a charm. Also very pleased with the speedy service you provided. Yours Truly Ron Ferro

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

I diagnosed the problem as a burned out element. Received the part the next day (very quick service) My husband replaced the old element with the new. My broiler still doesn't work. I don't blame the company, my diagnoses was wrong. I have called the appliance repairman and it will probably be an expensive fix.

Broiler element failed catastrophically (with light flashes) while in use (1986 GE self-clean oven/four burner stovetop). Part number embossed on element plate - very difficult to see - took digital photo while still in oven and magnified. Easy to search for part. Good price, prompt delivery. Removal of old and install new awkward because of access angle and my decreasing nimbleness, as well as oven control thermocouple and support bracket in way. But no technical difficulties. Hex head metal screws holding in element; Notched phillips metal screws holding bracing bracket (easier to put element in by removing one side of bracket). Screws difficult to remove as in much used oven 26 years, and thermocouple partially blocking socket ratchet wrench. Would have been easier with 1/4" short extension. Before detaching element, I used twist ties around the leads tied to a large plastic clip so as not to lose them into oven back. PartSelect part was made by GE, not secondary source. Perfect replacement for this old part - still available.

Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!

Just re-connected the electrical. Was the exact/correct replacement part. Repair successful. Thanks.

Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.

First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

The broil element was easy to replace. Start by either unplugging the unit from the wall or turning the circuit breaker off. I started by removing the two screws that hold it in the back. There was a support bar attached to the top with two screws also. After removing all screws, gently pull the element forward exposing the two wires. Make note of which wire goes to which terminal. I also clipped a clothes pin to each wire to prevent them from falling back through the hole. Disconnect the two wires and reconnect to the new element. Reattach all screws and you're done.

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Good directions

Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.