RB540SHS General Electric Range - Instructions

Removal old fashioned oven door handle took time after removing the oven door. New replacement handle was easy to install! Try to reinstall was long and finally got installed after 5 attempts due hinge on right side issue

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Pull out wires & replace element by putting wires back in then tighten...done!!!!

I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the burner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you

Prior repair job had spliced the terminal block wires with electrical tape; electrical tape caught fire while making pasta.

anyways, disconnect all power, remove burners, pull stove out. you'll need a 1/4" drive socket to get the back cover off; six bolts total. phillips head screw driver to unscrew the terminal blocks; replace with new terminal blocks; it did not seem to matter which wire plugged into the back. put everything back together. very easy.

I pulled off the back panel and the two wires were attached to the back of the know for the burner that did not work. I unhooked the wires, fed the new ones into the same slot and clipped the block in place. That was it!

Unplug the stove. Remover back panel. Remove coil and pan. LIft stove top. Remove screw(s) holding element in place and follow wires to the back of the stove and disconnect. Replace with new kit. Easy.

This is the second time the unit has gone bad. None of the other three burners has ever had the problem.

Thanks for having the part available.

Did the repair just like the video shows.

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

had the right parts and the installation was a breeze. Have new burner bowls and stove looks brnad new.

Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one

First and foremost I read each of the blogs from your site from other people who have repaired this part. It was great.
First I unplugged the stove. Removed the back plate of the stove by unscrewing 6 screws. Removed the heating element & drip pan. I lifted up the stove top to examine the receptable, and removed the receptable held in place by a single screw using the nutdriver.
Once it was removed, I cut the wires attached to the receptacle with pliers. I screwed on the new receptacle, and taped the new wires to the old ones which led back to the back panel where they were attached to the switch.

By doing so, I was able to easily lead the new wires to the back side of the stove panel. I removed each old terminal wire and replaced it with the new one. (I had read in a previous blog that the polarity of the new wires didn't matter). I replaced the drip pan, and heating element, turned the switch and everything was working just great! I replaced the back panel, and that was it!
As you probably can guess I have never attempted to repair any type of appliance...ever! But your website and the people who shared their stories empowered me to do the job. Thanks so much!

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

Easy

Since we got the stove,this is the second time we've repaired these connectors. The first time the connectors came with pre-stripped wires, wire nuts and heat shrink tubing. This set came with pre-attached spade terminals, so I had to crimp the mate to the wires in the stove then put heat shrink tubing on the splices. I also had to bend the part of the connector that mounts onto the stovetop. These had a horizontal tab for the mounting screw rather than the vertical design that our ranges uses. If the connectors designed for the earlier model were available, it would simplify installation since shrink wrap and wire wraps came in that kit and the mounting bracket would fit correctly.