JGP933SEKS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Mandeville, LA
- Parts Used:
- WB18T10339, WB13X46909
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Constant Sparking on front burners
Easy to replace - caution to make sure spark igniter switch is aligned and secured in correct position on the gas valve. The switch should cover both mounting screws on the gas valve when properly installed/aligned
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from Leesburg, VA
- Parts Used:
- WB18T10339
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One Burner would not light when using the corresponding knob..
Good way to tell/verify what your problem is. On my GE Cooktop, moving any of the knobs to light cause a spark for all igniters. One of our knobs would not cause a spark. - Remove gas grills and covers. - Remove screws - Pull igniters up (be gentle to not crack them - Pull wire out from igniter - lift cover of cooktop - pull harness off each know and disconnect two wires - put new harness on and connect and backfill. Pretty easy overall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Nashville, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Large burner wasn't lighting very quickly
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olegario from Whittier, CA
- Parts Used:
- WB18T10339, WB13X27058
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Ingiter Switch shorted; needed to be replaced
TURN OFF GAS and unplug stove. Removed burners (used screw driver to remove screws) and spark ignitors (used pliers). Lifted top cover of stove and unpluged the harness assembly(pulls out easily). Inserted new harness and replaced cover. Replaced burner parts included new spark ignitor. Plug power cord and turn on gas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara J from Sweetwater, TX
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Missing grate foot.
Ordered by phone parts & very pleased with all of transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Watertown, MA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the grate foots came off
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from mendocino, CA
- Parts Used:
- WB03T10242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace oven knob
press on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Kenner, LA
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Warren, NJ
- Parts Used:
- WB02T10461, WB29K10023
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Both items needed to replace broken or non existent ones
The burner cap was a no brainer. The grate feet should have been also, but many of them were undersized so we had to maneuver them in such a way that they didn't fall out of the grates.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Danville, IL
- Parts Used:
- WB18T10339
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
igniter kept igniting
Simply removed the 9 T9 screws from the top of the cooktop, removed the igniter spark modules, lifted the top of the cooktop up and removed harness assembly. Unplug harness from spark module and replaced in same fashion. SUPER EASY done in less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Knoxville, TN
- Parts Used:
- WB13X46909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spark module would constantly spark
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this instruction helpful to you?
Thank you for voting!