JDP39BKB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from EDENTON, NC
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Defective switch
Replaced element control switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from HOPEWELL, VA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Just didn't work no pwr to it
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from GAYLORD, MI
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
front lift burner not working and surface light on with everything off
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from BALDWINSVILLE, NY
- Parts Used:
- WB24T10025
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Surface burner stopped working & light indicator remained on
It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CHESTER SPRGS, PA
- Parts Used:
- WB23T10015
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven tempeture off by 50 degrees
Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from ELIZABETHTON, TN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would shut down while baking. Stove top would work.
Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from BENNETTSVILLE, SC
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven could not be turned off once settings were turned on except by unplugging hookup.
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from GORDONVILLE, TX
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Replaced drip pans
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lan from SANTA CLARA, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
It was burned out
I just follow Steve's Installation Vidio. My range works.
Thanks Steve
Thanks Steve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from SAN RAFAEL, CA
- Parts Used:
- WB30X20478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Top left electric burner on the stove top did not heat up
Simple to repair. Take off the cowling around the burner element on the stove top and pull out the old element. Slide in the new heating element with the cowling paying attention to the three spoke support areas on the stove burner frame. Very simple. A 5 minute repair. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from ORLANDO, FL
- Parts Used:
- WB30X20478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner was damaged so it didn't work
Easy repair, just had to take the damaged burner out and slide the new burner in....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from LAKE ELSINORE, CA
- Parts Used:
- WB25T10002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken light cover
twisted it in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from SAINT JAMES, NY
- Parts Used:
- WB30X20481
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had to replace the surface heating element on my Selectra stove top.
I just inserted the replacement where the old one had been connected. It took less than 5 minutes. It was so simple & easy that 'repair' is too generous a word -- & I am NOT handy, in any sense of the word. It took me longer to figure out where to find the model number!
Was this instruction helpful to you?
Thank you for voting!