J4790L1 General Electric Range - Instructions

A simple repair using your quality matched Part turned into a CONDOMINIUM CIRCUS (no fault due to the Part or PartSelect.Com.)

It was the 1st time in over 30 yrs. that we had to throw a Circuit Breaker Switch located outside in the communal large Metal Box between Condos. Not only did it NOT cut the power off our old GE Range - it turned off one neighbor's T.V. & another neighbor's Washer/Dryer Set.

As more Breakers were tried - MORE ANGRY NEIGHBORS ARRIVED ON THE PATIO. To complicate this - the next-door Condo just underwent extensive (read 3 Months) Renovation including REPLACING ALL WIRING..... and you might imagine the rest. No Breaker Switch numbers matched the Condo number written beside them in felt tip pen... it was complete chaos!
THANKS to PartSelect.Com our old G.E. is working again.

Yours truly,

William Rush,

removed old element rewired new element,turned back on power

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.

First my husband removed the screws that held the element in place, pulled it partially out and then disconneted the wires. He located the part number that was stampted on the defective element and then I searched the internet for GE parts. I noted the price at GE site and continuted to search. The PartSelect price was about 1/2 of the GE price. We ordered the part, it arrived in two days, and we replaced it in less than 30 minutes. We were very pleased.

Turned off the breaker to the range. Turned on range to ensure no electricity was currently flowing to the range. Turned the range off and unscrewed the tilt lock hinge. Pulled the burner out to expose the wires. Popped the snap locks off the cover box and unscrewed the wires connected to the posts. Followed recommend directions to expose approx. 1/2" of new wire (this is what I used the knife for since I did not have a wire stripper available). Slightly cut thumb in the process (no blood, though). Removed old burner. Put new burner in place, re-attached wires to the posts and screwed in to place. Placed cover box back in place and secured using new snap locks. Attached tilt lock hinge using new screw that was provided. Turned breaker back on and turned on range. new burner worked great. Took about 20 minutes total. Wife was extremely impressed, mostly that I didn't electrocute myself. She now wants me to replace other three burners. No good deed goes unpunished.

First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.

Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!

This was a second hand stove we have had for about 3-yrs. I noticed immediatley that the drip bowls and rings were not OEM parts & the bottom of the burners had actually been bent to fit the rings. I was very glad to find this website with a detailed diagram of the stove and parts. I intend to replace all the burners, drip bowl & rings, and then start replacing other parts as needed.

I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.

I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!

The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.

Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.

Just an easy replacement. Problem was, I couldn't find the parts. The service and turn-around was fabulous!