JGBP29DEMW General Electric Range - Instructions

Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

On each side of the door at the top you will find an allen screw, remove those to remove the handle assembly. On the inside of the door, you will find two more silver allen screws, these release the glass frame. On the flimsy part that seperates from the main door frame, there are two small brackets that hold the glass panel. Remove those using a #2 philips head screwdriver, then using a flat head screwdriver, carefully pry out all the ramaining glass shards. The glass frame will be very wobbly, this is a good time to have a friend around. place the new glass panel in the bottom slot first, then just hold it up, with a helper on one side, and reinstall the top brackets. These fit tightly on the glass, so expect to have to push a bit. now reinstall the screws, fold both parts together, use the silver screws to reconnect the glass panel assembly to the door frame, and reinstall the handle. Now you have a nice new door front!

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new lines came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

First remove the broiler drawer. I laid on my side and reached into the oven to do the work, I first removed the one screw holding the splash plate (in the rear) and lifted the plate out. Then, removed the two screws mounting the ignighter to the burner base. Cut the wires on the old ignighter about half way between the connectors on the safety valve and the ignighter. I used a utility knife to strip 3/8" of the insulation on the wires still connected to the valve. Then, mount the new ignighter. Route the ignighter wires behind the gas tube. Use the enclosed ceramic wire nuts to connect the new ignighter wires to the wires still attached to the valve. Push the wire nuts into the hole behind the valve. Reinstall the splash guard and broiler tray.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

From back, top of stove, removed 4 screws from panel to gain access to control unit. Removed 4 screws holding control and let hang from wires. Removed face plate from old unit and installed on new part. Installed new control and one at a time removed wires from old part and connected to new control. Replaced cover panel. Oven works fine now.

Removed the screw from the broken piece and put the new piece on and put the screw on.

This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams

Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.

I unscrewed to old glide and replaced it then re attached the screw

I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!