J301P3 General Electric Range - Instructions

Removed element and installed new element. Fit perfect, no problems.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, put the new one in and reversed the procedure. Also delivery was great, I ordered the part and received it the next morning. I highly recommend your service.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above

I double checked to make sure I got the right part.I looked at your video and then just did as you suggested. It was a easy fifteen minute job. Thank you for making this so simple to follow along with.

Turn off breaker for unit! Use nut driver to remove old element,and replace

Once I watched the video pertaining to the installation of the part, the job was very easy.

First of all the part came super fast with standard delivery. We threw the circuit switch to the oven. We used a nut driver to remove the nuts holding the element in place and then gently pulled it out of the hole so we could see the terminals. Using a screwdriver we loosened the screws that hold the terminals to the power lines. We put the old element aside and laid the new element on the floor of the oven. Using a screwdriver and the original screws we attached the terminals of the new element to the power lines. Using a screwdriver and the new screws provided we attached the bracket to the back of the oven. Turned on the power; used the oven. Works perfectly.

Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding element in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks

Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires into insulation and put back on shield.

Replaced lower element

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.

Removed the oven shelves. Removed two small screws in back of oven. Gently pulled out element to get to two other small screws connecting the element and removed them. Removed old element. Placed new element in oven connected the two screws to the element. Replaced two screws on back of oven. Replaced the shelves. That's all there was to it.

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

Following common sense, I removed the broken bake element by first removing two retaining screws and then disconnecting the element from the internal wires using a nut driver for both operations. The new element was installed in reverse order first using a screwdriver to attach the element to the internal wires (the new element had embedded threaded openings and came with two new machine screws) and then using the nut driver to secure the element to the oven wall.

First -- and thank goodness I read some of these stories first or I would have forgotten -- I turned off the circuit breaker to the stove.

I removed the two nut screws holding the element itself to the back of the over. Then I removed two more nut screws holding the element to the electrical wires. (This took some WD-40. The stove is about 25 years old.)

That was about it. Everything lined up perfectly, and there was nothing more to do except reconnect the new element and throw the breaker back on. It works!