JKP97G006 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paul from Hartland, WI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Original bake element quit working
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Dallas, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bake Element went bad
First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Portola Valley, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element cracked and started arcing. (Dramatic!)
First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.
Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.
Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RM from Woodinville, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element burned out
I got the help for the install from the help desk. It went EXACTLY as described, I'm so impressed. So got the best price and the best help and we're fixed and I'm baking again. Awesome
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- arthur from annandale, VA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Old burnt out element
Removed the two screws holding the mount and then reattached the two wires to the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Norcross, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
replace burned out element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Chapel Hill, NC
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace Broiler Element
After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wayne, OK
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lower heating element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Calhoun, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Overn would not heat properly.
Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Kalama, WA
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Blown Broiler Element
Removed 3 screws from cover {center of back side of oven}, removed 2 screws from wires connected to element, then removed 2 screws mounting element
{inside oven}, pulled it & replaced it.
{inside oven}, pulled it & replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harrold from Peru, IN
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Baking element was about to break into
Part was in stock, delivered in two day, Wow!!
First shut off power to the oven, the removed the two screws that held the element in place, pulled the old one out and disconnected it and put the other right back in. took less than 1/2 hour.
Very satisfied with product , easy of repair and especially the price and delivery.
First shut off power to the oven, the removed the two screws that held the element in place, pulled the old one out and disconnected it and put the other right back in. took less than 1/2 hour.
Very satisfied with product , easy of repair and especially the price and delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from Oceanside, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Bake element broke apart at 3 places.
Removed the broken one by disconnecting the two screws , yellow and red wires and replacing it with the new part you sent me. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Agnes from Rochester Hills, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat.
Shut the power off to the stove. Removed the screws and pulled the old part out. Replaced with new part from Parts Select.
Your service is excellent. I received the part within two days of it being mailed. The emails received from you were very helpful and also confirmed the transaction.
Thank you very much.
Your service is excellent. I received the part within two days of it being mailed. The emails received from you were very helpful and also confirmed the transaction.
Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candice from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bottom element caught fire and burned out.
You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Odessa, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
baking element burned out
replaced with a new part . Thanks for all your assistance in getting the correct part
Was this instruction helpful to you?
Thank you for voting!