JK140R1BC General Electric Range - Instructions

I read your website repair testimonials by previous customers and used that advise to do the job. I liked the suggestion to use something to attach to the unattached wires so they don't slip back into the unit. I used two clothespins. I had one stubborn electrical connection to disconnect so it took a little longer -about 30 minutes. But it was a simple job to do and my oven works fine again. The item was delivered timely from the order date and packaged well. Thank-you!

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

Shut power off to oven. Removed old element with socket wrench. Replaced old with new element, using socket wrench and new screws. restored power. That's it. Fortunately, old screws were not rusted. If they had been, would have used a rust solven.

Part was a breeze to install. I turned the power off to the oven at the breaker. I then unscrewed the bolts holding the old element in and disconnected the wires. I attached the wires to the new element and bolted it back onto the oven. I turned the breaker back on an tested the new bake element. Worked great! Now it heats up like it should. The whole process was very easy.

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

Removed the coverplate screws, slid the element outward, and removed the wire connecting screws. Positioned the new element to reconnect the wires, and discovered this isn't easy to see with trifocals. Succeeded after several failed attempts. Slid the new element into position, and reattached the cover plate.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.

shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!

Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

several months ago the bake element in my oven started cracking. When it started sparking I knew I had to replace it or get a new oven. I ordered the part and it was easy. The old one fell apart as I removed it. I honestly don't know how it was still heating. Anyway, all I did was turn off the electric to the oven, then I had to remove to screws that attached it to the wall of the oven. That was the hardest part because I couldn't see them well so I had to put a lantern in the oven. Then I had to pull it out enough to remove the screws from within. Then I just reversed the process to install and everything worked great! Saved me a lot on calling a repair man.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..Took out the old element and reversed tjhe procedure to install the new one

After an exhaustive search of local oven dealers and big box stores, I could not find a broiler element for my aged GE stove. I did find it online at Parts Select for about 1/3 the cost from GE online parts.

Replacement was easy-- just as described in posts for this part. The 'hardest' job was getting the screws started that hold the wires to the element-- small screws and small holes-- but just required some patience. A simple, inexpensive repair that avoided my having to replace the entire stove. Thanks!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.