JP661B3C2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES from STATE COLLEGE, PA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Contact Burnout Inside Terminal Block
Pull out oven/range unit. Lift range top all the way up. Remove old terminal block. Make electrical connections using supplied wire nuts & heat shrink tubing. Heat shrink. Replace range top. Install coil burner & burner pan as unit. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Hamilton, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from New smyrna beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Baden, PA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Montgomery,, AL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
Dirty and stained Pans and ring
Just pulled out the three burners and lifted the pans. Lifted out the ring. Pivoted up the 3-way burner, and lifted up the pan with wider slit. Put new ones in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Fayetteville, WV
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from South Daytona, FL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace the 6" surface unit.
My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Wilmington, DE
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
older element losing heat
really easy, remove old and replace with new...easy, once you have ordered and received the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Merritt Island, FL
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I could not find a dealer who could tell me what part I needed because the model was discontinued
I just went to your web page and indicated I needed an 8' surface element and up popped a picture; I ordered it and plugged it in and it works perfectly. I didn't need a model number, or a part number. Three cheers for a simple solution and a 1st class web page!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from wernersville, PA
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken heat element
Fit was perfect, slip right in prlace and works great thank u! R.e.Rice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudine from The Colony, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element not working
I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Austin from Blackfoot, ID
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Poor connection to element
In a little over 15 minutes, I was able to pull the element and pan, snip the wires on the terminal block and use the wire nuts to fasten the new terminal block. The shrink wrap tubing went into place easily and all went back together easily. Best of all, the two year problem of a poor element connection was solved in a matter of minutes for a few dollars.
Was this instruction helpful to you?
Thank you for voting!