JB710SM2SS General Electric Range - Instructions

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not slide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.

1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element with holes and tighten screws. 6. Plug in power cord and begin to cook.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Took the old racks out andcslipped the new ones in

Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift the front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.