JKP16G407 General Electric Range - Instructions

Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after reconnecting the new element the broiler tested OK. It is once again broiling steak to perfection

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-eyed peas and ham, a New Year's tradition in my neck of the woods.

I researched the part on the internet and found your website. My husband was able to figure out how to install the new element, following the instructions on the site. The most difficult part was reaching into the oven itself.

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.

Cut the power off to the oven. Removed both of the racks in the oven. Removed the 2 screws that hold each element in place. Pulled the bake element out as far as it would go and unscrewed the two wires. Then did the same for the broil element. It has a guard to keep it from dropping down and I had to remove that. The broil element is a little more difficult to remove but i had read that in the previous users writeups. Overall it was a great experience from a price, delivery and installation process.

First of all let me say, I am grateful you are supplying parts to an oven made in 1984. I noticed the crack the day before Thanksgiving and immediately started looking for the part because Thanksgiving was the least of my worries. I have a countertop broiler to cook the turkey and dressing in but I am catering a huge party in a week and really need the oven in top shape. Due to minor surgery I have not made the repair but I want to say thank you for getting the part to me on Saturday right after Thanksgiving. Wednesday to Saturday with a two day holiday is incredible. Thanks for the great customer service.

remove/replace baking element. Relatively simple to do; however, I used the old screws/nuts as they worked better than the new ones which were included.

Took out the old and put in the new! Easy and inexpensive repair (especially because my husband did it!)

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole expierence.

Throughout, I took care to not rest my full weight on oven door, although it's hard to work with arms extended. Shut off power to oven at outside circuit breaker, removed both racks, placed trouble light on open oven door at left to illuminate back of oven. Tilted element up to get at bolts. Used 1/4" socket set to remove two hex bolts holding burned-out element's plate to back of oven, pulled it out 3" to expose wire connectors. Held connectors still with pliers in left hand (to not bend wires) while loosening/removing connector bolts with socket set in right hand. Took effort to loosen. Removed element. Wiped oven floor clean. Positioned new bake element in same place, again held connectors still with pliers (left hand) and tightened wire connector bolts with socket set (right hand), pushed element back to original element's position. New element came with screws, not bolts, so used magnetic Philips screwdriver to get screws lined up (tricky), tighten new element's plate to oven's back wall. Removed trouble light, restored power, set closed oven for "bake" and "350 degrees." Element glowed hot in 1 1/2 minutes, ta-daah!

Took the old one out and replaced with the new one. It was just awkward to get at.

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!