JKP073J3 General Electric Range - Instructions

Took out the old and put in the new! Easy and inexpensive repair (especially because my husband did it!)

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which worked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed. Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!

First job was power off! Next step was to remove the two screws holding the element to rear wall of oven. Next is was to gently pull the wires through the hole as far as possible. At this point I needed pliers to stabilize the joint while I removed the two screws of the electrical connection. Now it was easy to clean the oven to remove arc residue. Now it was a matter of reassemble. Hardest point was getting the screws started in the electrical connections without cross threading while reaching in over the door. Use pliers to ensure you don't bend the connection wires on the element. Finally remount the element with the two original screws. This was the second element to fail. Last time I removed the oven door for better access. I think it was quicker with door on but a lot more bending and reaching.

remove/replace baking element. Relatively simple to do; however, I used the old screws/nuts as they worked better than the new ones which were included.

I researched the part on the internet and found your website. My husband was able to figure out how to install the new element, following the instructions on the site. The most difficult part was reaching into the oven itself.

Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after reconnecting the new element the broiler tested OK. It is once again broiling steak to perfection

Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.

First of all let me say, I am grateful you are supplying parts to an oven made in 1984. I noticed the crack the day before Thanksgiving and immediately started looking for the part because Thanksgiving was the least of my worries. I have a countertop broiler to cook the turkey and dressing in but I am catering a huge party in a week and really need the oven in top shape. Due to minor surgery I have not made the repair but I want to say thank you for getting the part to me on Saturday right after Thanksgiving. Wednesday to Saturday with a two day holiday is incredible. Thanks for the great customer service.

Took the old one out and replaced with the new one. It was just awkward to get at.

Shut power off to oven. Removed old element with socket wrench. Replaced old with new element, using socket wrench and new screws. restored power. That's it. Fortunately, old screws were not rusted. If they had been, would have used a rust solven.

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

Easy! Removed the screws, took out the damaged element, reversed the process with the the new element. I called in my order on Monday and Wednesday evening the oven was repaired! It doesn't get any better than that. Thanks for the great service.

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

I got the help for the install from the help desk. It went EXACTLY as described, I'm so impressed. So got the best price and the best help and we're fixed and I'm baking again. Awesome