J478B3 General Electric Range - Instructions

Just an easy replacement. Problem was, I couldn't find the parts. The service and turn-around was fabulous!

Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form the wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.

Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.

Replaced 30 year old stovetop cooking element with no problems. Stovetop works great now.

Threw away the old ones after lifting burner rings. Put new parts in place.

I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

Replaced old bake element by removing two screws holding it to back of oven. Disconnected old bake element from lead wires by removing two other screws. Installed new bake element by reversing the process. Only issue is that the tabs on the element that connect to the leads are easily bent and you need to use vise-grips to keep from bending them. Otherwise, very easy. Thank you PartSelect.com for stocking this item that I used to repair my 45-year old GE range!

could not find the proper pans and rings in any diy stores, as stove is so old. went on this site and there they were!!!

Placed new ones on range. Exactly what I would do to wash them.

The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.

Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.

I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!

Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!

Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussing. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.