JKP97G106 General Electric Range - Instructions

Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.

Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.

Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!

took out old then put in knew

Turn off circuit breaker. Release bake element from back of oven with a phillips head screwdriver. Remove bake element from heating wires with an adjustable wrench. 1/4 nutdriver was a little to big large for the old screw. Do not allow wires to fall back into the installation. Reverse the procedures for installing the new bake element. Most difficult part of the repair is having old eyes and not being able to focus on the work site which is about 12- 14 inches from your eyes. Young people with good eyes no problem. Oven heats like a new unit.

having read instructions from previous PartSelect users it was a snap. Nutdriveer, and screw driver were the only tools needed. This was a wall oven and the most difficulty I had was getting to the nuts with the door open. I really didn't want to take off the door.

I read your website repair testimonials by previous customers and used that advise to do the job. I liked the suggestion to use something to attach to the unattached wires so they don't slip back into the unit. I used two clothespins. I had one stubborn electrical connection to disconnect so it took a little longer -about 30 minutes. But it was a simple job to do and my oven works fine again. The item was delivered timely from the order date and packaged well. Thank-you!

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!

You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.

Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!

Part was in stock, delivered in two day, Wow!!
First shut off power to the oven, the removed the two screws that held the element in place, pulled the old one out and disconnected it and put the other right back in. took less than 1/2 hour.
Very satisfied with product , easy of repair and especially the price and delivery.

My Husband did the repair while I wasn't home. He didn't bother to shut off the power even though he should have. He didn't electicute himself or burn down the house and the oven works great so I guess it was a success!