J361*R3 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Nashville, AR
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Baden, PA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from New smyrna beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Louisville, KY
- Parts Used:
- WB19X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
could not set timer or clock
removed timer assy. with wires attached, then mounted new timer in place. Took wires off old timer and installed on new timer one at a time. Worked like a charm. Also very pleased with the speedy service you provided. Yours Truly Ron Ferro
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Corpus Christi, TX
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing burner element
I bought the replacement element for my 98-year-old aunt, and she installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Littleton, MA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element failed
lift up to 45 degree angle and pull towards you. This one went bad and the contacts welded themselves together. Took some shifting and tugging to free it. Normally, they slide in and out effortlessly, like any plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Cortlandt Manor, NY
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not keep heat
pulled out the old one pushed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ella from Tampa, FL
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pre 1992 6" plug in electric cooking elements- rusted out
Worked, don't have to replace an old GE combination range "Microwave Cooking Center" when the surface units rusted out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert R from Richmond, MO
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a burned out calrod unit
Simply unplugged the burned out one and plugged in the new one. It worked like a charm.
Was this instruction helpful to you?
Thank you for voting!