All Installation Instructions for General Electric Range 1J4021M2

Customer:: Sue from Brighton, MI
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Oven element broken

Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!

Was this instruction helpful to you?

Customer:: Erwin from minneapolis, MN
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Socket set

element was broken

replace old one with new one thank you.

Was this instruction helpful to you?

Customer:: Gerald from Lanett, AL
Parts Used:: WB44X5099
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

bottom heating element burn out.

got new part delivered two days after ordering. I turned off breaker, used a 1/4" wrench to remove the fasteners holding the heating element to the back inside wall of the oven. used screw drivers (one Phillips and one flathead) to remove the screws holding the heating element to the wires. ensure you pull the wires slight out (easily) to ensure they don't pull back into the oven wall. unplug the element from the wires, install new element in reverse fashion and voila, done.

Was this instruction helpful to you?

Customer:: Milt from Manchester, CT
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

bake element burned out

A socket set was used to remove the old element. New element was installed with a slotted screw driver and socket set. It took 15 minutes from start to finish to complete the removal and installation. Element tested OK. The bake elment was delivered overnite by Fedx.

Was this instruction helpful to you?

Customer:: Dee from Delray Beach, FL
Parts Used:: WB44X5099
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set

heating element in oven burned out

--ordered part on line ---It came in the next day without any extra charges for over night shipping! The whole thing with shipping was about $26 and so easy to install. Turned of circuit breaker, unscrewed element and screwed in new one.I was so impressed with 'Part Select'. I have never had a more efficient and inexpensive experience with online shopping. Thank you , I would highly recommed you to everyone! Dee

Was this instruction helpful to you?

Customer:: Kent from Wild Rose, WI
Parts Used:: WB30X356
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Replace Non-working stovetop burner unit (electric)

1.Shut off power to stove. 2. Lift up non-working burner. 3. Unscrew retaining screw that allows burner to tilt. 4. Lift burner out. 5. remove clips from ceramic holder. 6. Unscrew 3 screws holding element, write down which color is attached to which element, or label wires. 7. unpack new element, directions say to cut off and tip the leads with solder, but I re-used the old circle connectors. 8. Screw the wires back on the new element (using nutdriver) 9. place element in new ceramic holder provided, and clamp shut. 10. place element in stove top opening and screw in retaining screw (honestly I could not get this to work correctly, so I just left the element sitting in the hole). 11. Turn power back on. This could take as few as 5-10 minutes, but I allowed 1/2 hour for turning power on and off or moving the stove to unplug it.

Was this instruction helpful to you?

Customer:: Samuel from Beavercreek, OH
Parts Used:: WB44X5099
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers

Element burned out

Simply removed two screws to detach element from oven wall, removed two terminal wires then reversed the procedure to install the new element.

Was this instruction helpful to you?

Customer:: Frank from Beckley, WV
Parts Used:: WB30X354
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

one element suffered a small puncture where the heated element burned thru

The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.

Was this instruction helpful to you?

Customer:: Peter J from Oceanside, CA
Parts Used:: WB32X10013, WB32X10012
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

old stained drip bowls

I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.

Was this instruction helpful to you?

Customer:: Robert from Nashville, TN
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

Bake element burned out, oven would not get hot

Turned off breaker for oven, removed baking (lower) element, searched website to match up size, shape, and connector-type of replacement part. Placed order and received two days later. Mounted new part in 10 minutes, turned on breaker, and immediately baked fries for children. No problem. Much cheaper and easier than replacing entire built-in oven.

Was this instruction helpful to you?

Customer:: Tauna from Holladay, UT
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

bad bake element

Turned the power off. Loosened two screws to take the element out. Loosened two more srews to disconnect the element itself from the power. This job was easy squeezy. Within 15 minutes flat I was back on the couch watching old Seinfeld reruns. Two thumbs up for the peeps at Part Select.

Was this instruction helpful to you?

Customer:: Eunice from North Providence, RI
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers, Socket set

broken bake element

1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!

Was this instruction helpful to you?

Customer:: Cindy from VACAVILLE, CA
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burned out lower element

Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.

Was this instruction helpful to you?

Customer:: Craig from Anderson, SC
Parts Used:: WB44X5099
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

original bottom heating element melted down into wall

Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement part here in 4 days at new years. Part was only $18.45. Parts Select rocks!

Was this instruction helpful to you?

Customer:: Jeff from Cody, WY
Parts Used:: WB44X5099
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

bake element broken and bubbled

removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff

Was this instruction helpful to you?

1J4021M2 General Electric Range - Instructions