JK25003 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Duryea from Westminster, CO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn't up element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gainesville, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element cracked and arcing
First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from stuarts draft, VA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
bad element
first i removed two screws pulled that hold the element in then pulled element out about 3 inche disconnected the two wires now hot meals thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brian from temple, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
burned/blow out element
pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing bake element
Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyler from Dannemora, NY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt out
Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erwin from minneapolis, MN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
element was broken
replace old one with new one thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Anderson, SC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
original bottom heating element melted down into wall
Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement part here in 4 days at new years. Part was only $18.45. Parts Select rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Cody, WY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element broken and bubbled
removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eunice from North Providence, RI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broken bake element
1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from VACAVILLE, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out lower element
Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Jacksonville, OR
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Very low oven heat
Ordered new element (super-easy to select the right one at this site!). Turned off stove breakers. Removed two screws holding mounting hinge plate with nutdriver. Detached wires with regular screwdriver. Attached wires to new element lugs with screwdriver, using furnished new screws. Reinstalled element hinged mounting plate with screws and nutdriver. Only difficulty is 1) working bent over inside the oven because the wires are short, and 2) wire screws are regular, not Philips, with shallow slots so screwdriver slips out frequently.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert D from Fort Worth, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake heating element burned out
removed the old element, inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ventura, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element had cracked - arcing to oven base.
My oven is so old that the model # tag has been scrubbed blank. I search your site by Brand name and oven description. I found the pictured element in your listing and sized it up. Part arrived as promised. It was simple to install - power down oven via circuit breaker and remove 4 ea screws and removed defective element. Install new element and reattach via screws. Turn on circuit breaker and power up oven to test - all working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorraine from El Campo, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Old bake element burned out
First, I turned off the power at the breaker box. Then, I removed the 2 screws attaching the bake element to the back wall of the oven. Next, I pulled the element out a few inches and removed the screws holding the element to the wires at the rear of the oven. Finally, I reattached the new element to the wires with the screws and then reattached the element plate to the rear wall of the oven. I turned the power back on at the breaker box, and tried the new element. It worked! Also, shipping was real fast, like 2 days from the time I placed the order to receiving the element.
Was this instruction helpful to you?
Thank you for voting!