JKP68G0K3 General Electric Range - Instructions

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

Removed the old part by removing inside frame. Used a screwdriver to gently wedge it out, then had access to the screws holding it to the metal frame. The part needed (door trim) was white, but no longer available. I ordered the part in black color. The original part had faded from white to a cream. I took the broken part to Home Depot and they made up a paint that matched the faded color. I painted the part with a foam brush. Diluted the paint to avoid runs and painted several times. It went back together fairly well except make sure you use double back tape to hold glass assembly in place. It would be better if two people do this job. one holding the glass and frame while the other is attaching the door trim from the other side. The door trim has some snap in parts that go into the metal frame along the hing side, make sure that they snap in so that the door trim dose not touch the main cabinet when opening and closing the door.

Once I saw the gasket that was supplied it was really easy to see how to install it.
A hook on either end of the gasket gave me the clue on how to remove the old one.
Off with the old and on with the new in less than 2 minutes!!
Extremely easy!! Thanks Part Select for having what I needed!

replaced lights in refrigirator and freezer

Simple, unscrew and then re-screw

attached new support in about 5 seconds

Turned off power. Then loosened two nuts at back of oven. Pulled out old element and inserted new element. Tightened two nuts and turned power back on.

My husband removed the old element by shutting down the power, then unscrewing the element. Then he screwed in the new element and turned oven on for 5 minutes to break it in.

Very simple and so cheap!

Turned off circuit breaker, took two screws out to be able to pull element out from back. Took two more screws out to remove old element from oven. Did the opposite to install the new bake element. Turned power back on, and it worked fine.

youtube video it took maybe 10 minutes total to replace part. Easiest repair ever. Im a 50 year old woman and when I say it was easy, it was easy!

If the bottom heating element is not glowing red when you turn the oven on replacing this part may be the answer. Look for a spot on the old element that could indicate it has shorted out and no longer carries a charge.
Very simple to remove the two screws holding the element in place, pull the element out about 3 inches, disconnect the two wires, replace with the new element and reattach the two screws. Simple and effective. The new element is fast and responsive. Do this before any other suggestions to replace more complicated parts in the thermostate etc.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
the Replacement fit easily. Part was delivered the day after ordering even though I used normal delivery. Oven broke on a Thursday,ordered the part Friday morning, back in operation on Saturday

Removed screws from plate holding the element in then removed the screws from the wires attached to the element. Reversed the process and was finished. Oven is back in working order. (I am recently widowed and this is the first time I have had to do this type of repair)