JMP264D1 General Electric Range - Instructions

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.

First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.

Toughest chore was to find a tool to remove the two hex screws that held the element to the back of the oven. Once I found the proper tool, the rest was easy. Pulled the circuit breaker, removed the two hex screws, disconnected the two electrical leads and put the new part in and did everything in reverse. Probably saved over $100 doing it myself.

I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.

Removed the two screws that held the element in place. Pulled the unit out a few inches to get at the bolted wires. The hard part is reaching in the oven using bifocal lenses and trying to block out the oven light. Getting past that obstacle, the rest went very well.

Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element. Attached the bracket and I turned on the power. I then tested the oven and it worked.

followed instruction that came with the parts. Looks great and was easy to install.

First job was power off! Next step was to remove the two screws holding the element to rear wall of oven. Next is was to gently pull the wires through the hole as far as possible. At this point I needed pliers to stabilize the joint while I removed the two screws of the electrical connection. Now it was easy to clean the oven to remove arc residue. Now it was a matter of reassemble. Hardest point was getting the screws started in the electrical connections without cross threading while reaching in over the door. Use pliers to ensure you don't bend the connection wires on the element. Finally remount the element with the two original screws. This was the second element to fail. Last time I removed the oven door for better access. I think it was quicker with door on but a lot more bending and reaching.

remove/replace baking element. Relatively simple to do; however, I used the old screws/nuts as they worked better than the new ones which were included.

First of all let me say, I am grateful you are supplying parts to an oven made in 1984. I noticed the crack the day before Thanksgiving and immediately started looking for the part because Thanksgiving was the least of my worries. I have a countertop broiler to cook the turkey and dressing in but I am catering a huge party in a week and really need the oven in top shape. Due to minor surgery I have not made the repair but I want to say thank you for getting the part to me on Saturday right after Thanksgiving. Wednesday to Saturday with a two day holiday is incredible. Thanks for the great customer service.

Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-eyed peas and ham, a New Year's tradition in my neck of the woods.

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

Easy repair. The toughest part was disconnecting the wiring from the old element. Once that was disconnected it went very well.