JKP76G*02 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Laurence from Durham, NC
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Element bad
New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in same position. If we had called a eepair company it would have taken a week or more and probably been expensive!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeanne from bodega bay, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
bake element was fried
husband said he would call repairman. I found you and ordered part. By the time my husband got around to calling the repairman, I was finished.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.
Only trouble was getting my hands to work in the small space. The cover plate was not as big as the former unit so I had to muscle it on. BUT, it was a very easy process and we saved tons of money on a repairman and a new oven/micro. THANKS.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from Barkhamsted, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element caught on fire and melted
My Husband did the repair while I wasn't home. He didn't bother to shut off the power even though he should have. He didn't electicute himself or burn down the house and the oven works great so I guess it was a success!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Tehachapi, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not heat up fully
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and made sure that there was no power feeding the element. Next I disconnected the two wires that power the element. I then removed the old element and replaced it with the new element. Tightened the screws but had to be careful on the second one and hold with plier as the first one bent a little as it was being tightened. Slid the element back after the connection screws were tightened and tightened the mounting screws. Reenergized and tested. The job went well - easier than expected...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Hartland, WI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Original bake element quit working
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires on the element. Put in the new element and reconnected the wires. Pushed the wires and element back into place and screwed in the screws that hold the element in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jerome from Farmington Hills, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
heating element was on fire and needed to be replaced
shut off circuitbreaker.removed two screws.kind of hard since screws were 25 years old and were tight.then i removed the oven door and pulled out the elementout and removed two more screws that held the wires to the element,then removed the element and replaced the new one and screwed it to the wires and thenthe next two screws that held the element in place. turn on the circuitbreaker and it was a miracle it got hot!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Des Plaines, AL
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bake element failed
Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHY from QUINLAN, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
baking element burned out
Turned breaker off to oven. Removed 2 screws from burned out element in back of oven and pulled it out. Installed new element and tightened the two screws. Very easy.
My oven is 31 years old so was suprised I could still get parts.
My oven is 31 years old so was suprised I could still get parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Portola Valley, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element cracked and started arcing. (Dramatic!)
First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.
Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.
Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelley from Cleveland, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The baking element was old & sparks were coming from it..
I (a woman) unplugged the stove, took out the screws, and unhooked the baking element. I then replaced the old screws with the newer ones, and made sure everything was nice and tight. I was a little nervous at first but everything turned out okay. I plugged the stove back up & the baking element was a bright orange and it works better than ever. The whole process took about 15-20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Westfield, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
original heating element broke in 2
Unscrewed the broken element from the back of the inside of the oven, then unscrewed the connected wires from the element and did the reverse with the new element. Viola.
Before touching anything, however, I made sure the oven was in the off position and also went to the house circuit breaker box and flipped OFF the appropriate circuit breaker(s). There were two - one for the element and another for the rest of the controls.
When everything was in place, I turned the power back on and turned on the oven and was cooking again. We had Prime Rib for Easter.
Before touching anything, however, I made sure the oven was in the off position and also went to the house circuit breaker box and flipped OFF the appropriate circuit breaker(s). There were two - one for the element and another for the rest of the controls.
When everything was in place, I turned the power back on and turned on the oven and was cooking again. We had Prime Rib for Easter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Lombard, IL
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
the bake element was cracked and falling apart
several months ago the bake element in my oven started cracking. When it started sparking I knew I had to replace it or get a new oven. I ordered the part and it was easy. The old one fell apart as I removed it. I honestly don't know how it was still heating. Anyway, all I did was turn off the electric to the oven, then I had to remove to screws that attached it to the wall of the oven. That was the hardest part because I couldn't see them well so I had to put a lantern in the oven. Then I had to pull it out enough to remove the screws from within. Then I just reversed the process to install and everything worked great! Saved me a lot on calling a repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wayne, OK
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lower heating element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Naperville, IL
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake element in lower oven would not heat
Removed the bad part. There were 4 screws,
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.
Found part on the internet.
When part arrived I installed it using the screws that I removed when I took out the bad part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Dallas, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Bake Element went bad
First I Shut off the breaker from the fuse box
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven
Tried to turn oven on to make sure I tripped the correct breaker
Removed element from back wall of oven by removing 2 screws using a socket set
Gently pull out element a few inches and then unscrew 2 wires from the bake element using a phillips screwdriver
Replace old element with the new one
Screw wires to element
Attach new element to back wall of oven making sure the rectagular hole is totally covered and the element is flush against the back wall
Replace screws attaching baking element to back of oven wall
Turn on breakers and test the oven
Was this instruction helpful to you?
Thank you for voting!