7171192 General Electric Range - Instructions

I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.

I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had frozen pizza 20 minutes later.

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worked great!

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

My neighbor, a retired electrican, came over and almost had to take apart the total oven to get at the igniter. It was very difficlt to get at and take off. I don't know who disigned this, but it sure was not designed to fix easily. Products are not designed to be fixed. The companys want us to buy new products. America is a throw away society. Anyone trying to fix this part on their own: Good Luck!

Just replaced the igniter, was pretty easy

Took the pan off the bottom of oven (2 screws). Took one screw out of burner to get at igniter. Removed 2 igniter screws with ratchet which was a little difficult. Then cut the old wire since I was provided with wire nuts and using the old connectors and wire nuts, rewired the igniter and replaced the screws and replaced the pan on the bottom of the oven. Access to the wires is through the bottom pan by removing the drawer.

Your web site depicting igniter was perfect in helping me diagnose prob. Two other commentaries by people who fixed the same problem were also right on. I had to take out a second plate below the top ( primary ) drip plate, & above the warming drawer. Though akward to lay on one's belly to fix, all went well. Started right up & Christmas cookie -baking ensued. Great web site, great instructions. Thank you very much. Jeff M. PS, I initially went to another web site, starting with an "A", and found it hard to use & vague.

FIrst, have the tools you will need, a straight ratchet screwdriver, 1/4" ratchet/screwdriver set, a 90 degree offest, some small plastic bags to hold/tape screws to the pieces you take apart, and a flashlight.

1) Turn off the breaker to the oven.

2+ 3) Take the oven door off. It simplly lifts straigh up off the hinges. ( It slides back on hinges when you're done.) Take off the botton kick plate by pulling top down. The botton in on a hinge.

4) Slide out the oven racks.

5) Take out the inside bottom cover of the oven which is inside the oven. The cover lays flat and is attached by two screws in the back inside corners. You have to lift it up/out back edge first. (Put it back front edge first, & realign screw spring clips if necessary)

6) Slide out the oven gas line/igniter cover, which is found immedicately under the oven cover, by taking out one screw front center. You will then see the igniter in the back of the oven next to the gas line. *DO NOT UNDO ANYTHING HOLDING THE GAS LINE*.

7) From under the oven, take out two side screws helping to support the botton tray, one each middle side. Then take out the two most front bottom screws. while holding the front edge up. (It will drop) Then slide it out of groves in the back of the oven.

8) Take out the inside cover (2nd botton cover) by taking out the two screws from the inside front top. It will also slide out. This will totally open up access to the igniter bracket attacked to the gas line. *NOTE CURRENT PLACEMENT OF IGNITER WIRES*

9) Take off the two igniter bracket screws. Put the new igniter in its place.

10) Cut one wire off the old igniter as close to the old igniter part as possible. *YOU WILL NEED ALL THE EXTRA WIRE* *DO ONE AT A TIME* Match the same wire position old to new, strip 1/4", twist and ceremic wire nut provided together. Do the same with the second wire.

Put all parts back in reverse order.

put the new part

well part was correct .Got it fast son installed it so do not know what tools, But at last one think i did clean under the stove, which was needed. Would do business again if needed.
Thank you

The broiler still worked, so I knew the issue was not with the power or gas to the oven. It was easy to remove the inside bottom of the oven to look at the igniter and burner. 4 screws hold the oven bottom in place. After the igniter was in view, I turned on the oven to see if it glowed, which it did not. 2 more screws out and the igniter was loose. The two wires coming out of the igniter go through a hole in the back of the oven to a compartment below the oven. This compartment is accessed by removing the bottom drawer and removing a panel in the lower back of the oven held in by 4 screws. After disconnecting the wires, I attached a thin pull wire to them then pulled the igniter out through the oven door. The pull wires made it easy to feed the new igniter wires through the back of the oven. The rest is a reverse of the process.

To diagnos i removed the lower tray and could see the ignitor was not lighting like the broiler was,the same ignitor.I had the same problem as some of the other people so that was helpful.I removed bottom storage tray and could get to the wires and it was an easy fix,took about 40 minutes total.This website was very helpful also with excellent service on the parts and i saved a bunch of money!
Thanks,Gerald

First I got on line to make sure I had the right part. After it was delivered I started the project by unplugging the stove! A magnetic end for your socket device is very helpful.:-)A good alternative light source is esential to see what's going on.There is no need to pull out the stove.I then took off the oven door which is an easy process(Pull up off the hinges). I also removed the oven grates and lifted out the bottom plate which included the heat defuser.I then took out the storage drawer. The next step was to remove the rear screw and front 2 screws holding the burner tube. Then it was just a matter of pulling up on the tube and removing the screws holding the igniter.The 2 wires were then cut and the new igniter wires were spliced in with the new wire nuts that came with the package. I also used a little electrical tape to hold things in place. Then it was just a matter of replacing everything in reverse and plugging the stove back in. Everything works fine.