7171192 General Electric Range - Instructions

my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it.
I had the schematic picture of the door ready in case he needed it. He didn't really.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

After receiving the part ordered in one day, I removed the racks and the bottom flame spreader. The igniter assy. is held in by two screws, which only took a minute to remove. I removed the ceramic wire ties from, the old igniter and wire tied in the new one. Put everything back together and tested the oven. It works great again. Thanks for the quick response and delivery.

First I removed the pan drawer. Then I removed the metal cover under the stove. Not sure if you have to remove that or not. I think I could have left that on. I then looked inside the oven and removed the two screws in the back to remove the lower cover. Ahh, the hot surface ignitor and flame grill exposed. I then turned on the oven again to make sure the hot surface ignitor was not glowing. I went back underneath, and disconnected the hot surface ignitor. I followed the wires from it to where it was connected. I then unscrewed the 2 screws that held the flame grill in place. Next, I went back in the oven and removed the flame grill with the hot surface ignitor still attached. I then unscrewed the hot surface ignitor and replace it with the new one. Key points: make sure you mark which wire had which connector, or only cut one at a time. Also, they do not come with new clips, so don't cut you wire too short. I then fed the wires and the base of the flame grill back down the slot, rescrewed the flame grill to the oven, attached the wires, and turned on the oven to make sure it worked. I finally replaced the lower plate inside the oven, the lower plate under the oven, put the drawer back in and I was done.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Removed old gasket and pried out clips with screwdriver. Installed new gasket.

First remove the broiler drawer. I laid on my side and reached into the oven to do the work, I first removed the one screw holding the splash plate (in the rear) and lifted the plate out. Then, removed the two screws mounting the ignighter to the burner base. Cut the wires on the old ignighter about half way between the connectors on the safety valve and the ignighter. I used a utility knife to strip 3/8" of the insulation on the wires still connected to the valve. Then, mount the new ignighter. Route the ignighter wires behind the gas tube. Use the enclosed ceramic wire nuts to connect the new ignighter wires to the wires still attached to the valve. Push the wire nuts into the hole behind the valve. Reinstall the splash guard and broiler tray.

Remove the burner grills. Lift the stove top and lift the burners and unscrew the existing orifice spuds using pliers. Screw on the new (Natural gas) orifice spuds.

This oven is from 1993 and a lot less complicated than today's models probably are. The first things to do are to remove the oven door and broiler pan. On this model, the oven door simply lifts off the hinges. Once these are gone, you want to remove the oven floor. To remove, locate the two screws at the back of the floor. After removing, lift the floor up and towards the back to pull the floor tongue out of the groove in the front. This will expose the gas jet and ignitor assembly. At the front of the jet pipe is a screw that holds the pipe to the front center of the frame - it is underneath so you may have to bend over to see it, it can be felt easily as well. Remove this screw, this will allow the pipe to be moved a little later. In front of the assembly is a vertical metal plate with a screw at the right of the mounting the plate into the broiler floor. Remove the screw and slide the plate to the left to pull out another tongue/groove set-up. Now you should see the wires completely and the connection to the air-flow adjuster. There is a small screw in the front of this brass fitting, it does not need to be touched. Turn the burner pipe clockwise while lifting and this should pop the assembly up. The ignitor is mounted to the burner pipe by 2 screws that are found on the bottom of the mount. Remove the 2 screws, this will allow the ignitor to hang free. Be sure to pay attention to what wire attaches to what wire, I marked the left wire so that I knew which to reconnect to after the change over. Remove the caps on the wires if this unit has been removed before, if not then mark the wires on both the replacement unit and the original wires. My ignitor has been replaced before, so I used my wire cutter to clean-up the ends of the old connection before reconnecting the new replacement. At this point, you should be able to fire-up the oven, it might take a moment for the new one to warm up, so give about 30-40 seconds. If the oven fires up, it's then working to put everything into place in reverse order. I like to line up the parts and pieces as I remove so I can just put back in reverse.

took lp spud out and put in natural gas spuds.not sure what to do with oven yet it does not work now.

This was a real easy repair. The key is to remove the door (by lifting straight up) and remove the bottom drawer. Then take all the trays out of the oven, using a screw driver remove the bottom pan that hides the burner and igniter. From underneath the oven (ie drawer space) use a screw driver to disconnect two screws that hold the burner assembly against the back wall of the oven. Then remove the one screw from inside the oven that holds the burner assembly (its close to the door area). Unplug the two igniter wires from underneath the oven and then lift out the entire burner assembly. Take off the two screws that hold the old igniter to the burner and replace with new igniter. Make sure you mark the wires when you remove them because you need the connectors on the end for the new wire. Then give yourself plenty of wire, cut the old wire off the old igniter and using the provided wire ties join them to the new igniter wires and reconnect everything. Sounds complicated but it took me about 20 minutes and its really an easy repair. Good luck.

I was a bit hesitant to perform this repair but attempted it due to the other write-ups which were very helpful. The repair went very well and was quite easy. There was a suggestion to remove the gas defuser (the pipe thing that has the igniter attached), I believe loosening this defuser made the whole repair so much easer and quicker. Trying to remove the two screws that hold the igniter without this approach would have been very difficult. I was hesitant to do this but removing the 3 screws that hold the defuser in place was not a problem at all.

Replaced old with new.

First just unscrew each natural gas jet and install the propane jets. if they are hard to come off just turn your wrench back and forth first until the jet turns with your fingers. Then open the oven and take out the racks. In the bottom back of the inside of the oven there is a screw on each side. Unscrew both screws lift the bototom plate of the oven and slide it back about 1/2 inch then lift out of the oven. Move the 1 screw covering the heat shield from the oven jet. Then light the top burners and turn them off just to get the gas flowing. Also light the pilot in the oven, then light the oven. To convert the oven from natural gas to propane all you have to do is adjust the jet while the oven is lit. turn the oven jet ubtil there is a blue flame with little or no yellow tips on the flames.

1. Removed oven door.
2. Removed shelves.
3. Removed oven bottom.
4. Removed pan drawer.
5. Removed the 2 burner mounting nuts at back of oven pan drawer opening.
6. Removed top burner nut.
7. Pulled igniter out from top.
8. Snipped igniter wires.
9. Removed igniter from burner
10. Attached new ignitor wires with the enclosed wire nuts.
11. Attached new igniter to burner.
12. Replaced burner.
13. Pushed excess wire out of the oven through opening at back of pan drawer.
14. Reinstalled burner mounting nuts at back of drawer.
15. Reinstalled burner nut at top of burner
16. Reinstalled oven bottom, oven door and pan drawer.