JB968KKC General Electric Range - Instructions

popped the new one on!

Easy

I got someone to look at the stove. They told me what I needed. I looked all over the Internet and couldn't find the part. One guy told me just to buy a new stove top because mine was an antique. It still looked good and two burners were still working. I didn't give up. I found the part on partselect bsite and was thrilled. It shipped fast and was exactly the right part. Now my stove works like new.

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Followed directions from Rodney of Erath La. Directions were perfect and helped me to decide to under take this job. Job took a little longer spending some time to clean the glass top on both sides and around the counter top where it mounts. The actual repair time was quick and easy thanks to Rodney. Price of the part was reasonable and delivery got here quick. Will deal with parts select again! Carl from Florida

It is first necessary to remove the door from the range according to the manufacturer's instructions. Once removed, lay it down on a flat, protected surface with the outside facing down. Remove the two upper phillips screws and the hex nuts on the bottom channel. Next, separate the inside panel from the outside panel. You will then see the remaining hex nuts that have to be removed in order to replace either the bottom trim channel or the side pieces.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

remove two bolts in on sensor and slip thru back un plug and reverse to put in

Went super fast--very easy. Part fit perfectly and the installation was a snap.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Turned off the power at the breaker. Then I lifted the cooktop by pressing up from the bottom, while my wife slid two boards over the recess. I lowered the cooktop onto the boards, removed 12 screws around the perimeter of the case and carefully lifted the glass top and placed it on a towel on the DR table. (remove the control knobs first) removed the wires leading to the infinite control, marking which color when where, removed the two screws holding the infinite control, and replaced the old with the new. Reattached the wires, replaced the cooktop, replaced the screws, held it up while my wife removed the boards and then carefully lowered the cooktop into the recess. Attached the knobs, flipped the breaker back on and turned control to hi. It worked!

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.