JBS55CKC General Electric Range - Instructions

Unplugged Stove. Removed two screws. Unplugged two wires from heating element. Connected the two wires to new heating element. Replaced screws. That's all. 5 minute repair job.....(45 minutes to find right socket haha)

Ordered new heating element on Friday afternoon (3pm) and received part on Saturday at 1:00pm. Impressive! (standard shipping)

removed the two screws,then pulled element out and removed the wires,took out element that needed replacing, then connected new element . the repair job took no time at all. i was really impressed with how easy it was.

I had my husband fix it! Very easy for me.

It didn't take him long. The most difficult part was getting to the screws. He had to practically climb into the oven.

The parts were shipped promptly and the whole process was relatively painless!

First I turned off breaker, pulled out oven unplugged/or dissconnected electricity to oven, unscrewed broken element in oven, unscrewed back panel of oven to disconnect 2 wires from element, and replaced with new element, then repeated the above in reverse.
Very easy for a typical DYI person.

The repair was so simple. First i killed the circuit breaker then removed five screws upluged element from contacts and removed the element plugged new element into the contacts popped the screws back and was done.

Easy

Unplugged the power supply. Took off the cover on the back of the unit. Unplugged the wires to the broiler element. Removed the bolts(4) holding the element inside the oven. Removed the temprature sensor from element and took it out. Put it all back the way it came out. Worked great. Took 25 minutes.

We ordered the part, it arrived quickly my husband removed the burnt out element. We took the back off the stove in order to install the new part. It was easier to connect from the back than reach in to the oven. An easy repair and the stove works fine now.

First I removed the screws and popped off the existing element. One of the wires "disappeared" back into the insulation, so I had to remove the back panel of the oven to access that wire and push it back through the opening. Then I attached the new element to the wires and replaced the finishing screws.

It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.

replaced Plastic Guides

Removed the door undid the two screws inside top of the door, removed bottom plate, installed new glass and replaced inside pannel and lower plate, installed door back on range

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.