JGBP28BEL3CT General Electric Range - Instructions

First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore name on it.
I found out that even though the old ignitor glows well, it may not pull enough amps to open the gas valve.
First i disconnected the two wires on the gas safety valve that lead to the ignitor. These are accessed after taking the bottom drawer out. Then using a nut driver, i took out the two screws holding the bottom of the burner tube. Then inside the oven, i took out the racks and then the two screws in the back on the bottom. Then took out the bottom plate. I removed the one screw on the front of the burner tube, and removed the burner tube with the ignitor attached. I cut the wires off the old ignitor and attached them to the new ignitor with the supplied ceramic wire nuts. I attached the new ignitor to the burner tube and put everything back together. The bottom screws on the burner tube were very difficult for me to reach. Almost impossible to get both hands there to do the job.

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as someone has said all in all it saved us 100 dollars and could have saved us months of burning food trying to cook on broil if i had only called the plumber first.ha ha

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new igniter and then replaced everything by just reversing all that I did. Simple! Easy!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

I frist remove the screws that hold the element in place disconnected two wires.That didn't take long.Call aronud my area for part.They wanted 90.00 plus taxs.Went on line to find it much cheaper came in the mail very fast and put it in my self.Very easy and saved money too.It took less then 3 mins to put in.If I could do it you can too.Thank You,Bearice & Robert Reynolds P.S works great and no yelling at each other.Easy

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse order. Tested oven operation to ensure that the gas ignited promptly. (It did).