JBP22308 General Electric Range - Instructions

Pulled out the bottom drawer of the stove and discovered the plug. So the plug was pulled from the wall socket.

Before this I had sprayed the screws with WD-40 and let it sit for 2 days.

Screws came out easily. Pulled out the old element and removed screws. Screwed on new element on both sides. Put in place and put old screws back.

Plugged stove back in. Turned on stove. Element came right on.

super easy - unpluged stove - unscrewed old element w/nutdriver from back of stove. unwired element - discarded. wired new element (2 wires). secured new element to back of stove. pluged stove back in. works great. Ordered part on Sunday, recieved it on Tuesday- VERY NICE SERVICE

TURN OFF CIRCUIT BREAKER before doing anything even if oven is not turned on! If I hadn't checked voltage with tester before starting I would have made a shocking discovery.
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.

The element was 25 years old and I was concerned about changing it. But is was so easy. I turned off power and removed 2 screws and then unscrewed the wiring from the old element. I had the new one installed in minutes. I was so glad to have my oven working again. Who needs a man.

I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct part shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.

First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.

First I made sure the electricity was off. Then, I flipped the burner up, and loosened the screwon the hinge. This allowed the burner to extend onto the cook surface. After loosening the clips holding the ceramic insulator together, the wires to the element were exposed. The wires were then transferred to the new burner element from their corresponding position on the old one. The new ceramic insulator was affixed over the wire with clips, and the hinge reattached. The chrome ring was worked over the burner, and the burner reseated in its proper cook poistion. Testing confirmed the burner to now work as new.

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.

First I turned the Breaker off for the Oven. I removed the two screws that hold the element/cover plate. I pulled the element out to get access to wires attached to element & removed screws holding wires to element. I reversed the process to put back together.

The repair was fairly easy. Removed the 2 screws that hold the plate to the oven and then pulled out the element and loosen up the screws that connect it. Installed the new element and re-attached the element to the plate and secured the plate back to the oven. This site was very easy to use and very helpful and I will use it again if I need another part.

Shut off the power at the circuit breaker, removed the two nuts holding the element to the oven, unscrewed the two screws connected to the wire leads, removed the bad element and reversed the process to replace with the new one.

Followed the enclosed instructions

1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.