JCS966TD1WW General Electric Range - Instructions

Circuit breaker off. Watched You Tube video to easily remove and set aside oven door, and shelves, unscrewed back wall cover over convection heating element, and slid out cover over floor heating element. Used ratchet to easily disconnect both old heating elements & pull from rear wall, holding onto two clip electrical connectors while gently pulling out plenty of slack as wires fed through insulation material. Concern of "losing" wires back into oven wall not truly a problem if careful. Both sets of connectors pulled off, easily and then slid onto replacement elements without trouble. Circular convection element screwed back into place and cover replaced. Replacement floor element was similar, but not identical, to original. Wires connected fine, but base plate and two screw holes to attach to rear wall were of different size. It rests underneath oven lower cover on its own feet, so really didn't require support. Being DIY obsessive, I nonetheless used its base plate as template to drill two new holes in oven back, secured with old screws. Replaced cover, shelves, door, and woking like new!

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .

Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.

First, I turned off the power. I removed the fixture that held the bulb and gently used narrow type pliers to pull the old pins out and allowed the broken glass to fall upon a shop towel in the bottom of the oven.

The replacement bulb and different type of wiring connections. I cut and formed them to fit the receptacle. I gently inserted the new bulb, placed the glass cover back on. Then, screwed the unit back into the top of the oven.

Happily, when power was turned back on the light shone brightly!

Remove two screws hold cook top down: prop it open with piece of wood. (TURN OFF POWER TO RANGE FIRST!). Carefully make diagram of where wires go: remove and replace.. piece of cake!

RE: 2 yr. old GE double wall oven with convection option in upper oven, non-convection in lower oven: baked goods were not browning, were undercooked or burned. Tested both ovens on regular bake setting using 2 oven thermometers. Set ovens for 350. Although after 10 min both ovens beeped "ready", the oven thermometers actually read 200 - then would swing up as high as 500 and as low as 200 during the 20 min test period. Decided to first replace top oven sensor only, just in case it really was a more expensive control panel problem. It was a bit awkward to reach back there with the oven door in the way, but I have long arms! Aimed my flashlight, removed nuts with a socket wrench, pulled out the sensor, popped the clip and the old sensor easily separated from its connection. Snapped on the new sensor, pushed it back in and reset the nuts. Easy. Set the oven for 350 and tested again with 2 oven thermometers for 45 min. Voila! The oven thermometers read exactly 350 when the oven beeped "ready" and it stayed at 350 throughout the entire 45 min retest period with only a 3 degree variation both up and down. What a great improvement! Immediately went online to Parts Select and ordered another sensor for the bottom oven which was having the same problem. Fixed both ovens all for under $30 - and just in time for Christmas cookies! Don't want to know what the repair guy would have charged.......Merry Christmas!

Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

The oven lamp shattered while cleaning. Easy to replace by hand.

Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.

Removed back panel, change out sensor

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.