JBP65DMW General Electric Range - Instructions

Remove old stained gasket and replaced with new. Only $57.00!

I just removed the drawer and installed the rear supports as instructed on paper included with the part.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

turn off power to the stove
Pull the stove away from the wall
remove center (metal) wire cover (5/16 nut driver needed)
disconnect 2 quick connect clips
back to the front of stove, open oven door
using 5/16 nut driver, remove 2 screws
pull out old element
insert new element
using 5/16 nut driver, reinstall 2 screws
go back to the rear of stove
reconnect 2 quick connect clips
reinstall center (metal) wire cover (5/16 nut driver needed)
turn power back on
ready to cook

Being that the rest of the stove was functioning fine, it was still plugged into the electrical outlet, after unplugging the range, I used a nutdriver and and removed the back panel exposing the two electrical clips on the old heating element. After unplugging the two electrical clips, I removed the two screws that secure the heating element to the back of the inside of the range. Once the screws were removed, the heating element came right out. I inserted the new element, installed the two screws previously removed, plugged the two electrical clips on the back of the heating element, re installed the back panel, plugged the range in and cooked lasagna. Total repair time was 12 minutes.

unplugged stove-removed cover in back of stove-unplugged element-inside oven removed two screws-removed element. reverse procedure to install. took about twenty minutes.
wife happy again.
parts came in two days. I could not believe how fast it came. Thank You very much! Jim Jewkes

Just put 2 screws in. It was simple.
Web site very good details for finding parts.
Fast turn around from order to delivery.
Very satisfied!!!

I had read some of the other comments about the repairs. The one that I found most useful was the one describing how short the connector was once they are removed. That isn't a joke about 3/4". My sujestion is to have tape and tape them to the back of the oven so as to not to loose them in the insulation. Once that was removed and reconnected the oven worked again like new. Even the most novice of people will find it a breeze.

First, I read what other customers posted on this site about how to change the element. =)

I didn't have a nutdriver so I used a pair of pliers instead. They worked fine.

Pulled the stove away from the wall, unplugged it, removed the 4 small nuts holding the small plate over the back of the element connections, slid the connectors off the element prongs, removed baking racks from oven, removed 3 screws holding the element in place, slid element out.

To put the element in I simply did the same thing except in reverse order. The entire process was so easy and only took minutes to complete! However, like another poster, I took the opportunity to clean my oven before putting in the new element.

The best part of dealing with partselect....the element only cost me $51 vs GE site price of $91, Plus the element arrived the morning after I had placed the order! Thank you partselect! In gratitude, I posted my happy experience and a link to this site on my facebook! Thanks for everything!

Removed back cover to look at connections
which were a push on type connector. pulled off
connectors. there is insulation around element
Removed old element, using a nut driver from inside oven. Installed the new element the same way.Reinstalling the connectors, reinstalled the back. less than 10 min. Was very easy !

I am a recently divorced mom who is too proud to ask for help. When I received the part I took the time to read all of the previous posts. I did exactly as many people suggested: pull the oven out, unplug, clean up since you're back there anyway, used the nut driver to remove the metal plate in back and unscrew the two in the oven, carefully unclipped the electodes from the old element with the needle nose, remove the old element, insert the new element, reinsert the electodes , tighten all nut both in the oven and the large metal plate in back , plug back in, push the oven back in place. I reset the clock and also did what one person mentioned which was to turn the oven on and let heat up for about 20 minutes to burn off any of the manufacture coatings that were on the new element. This did not even take me 15 minutes! I was so proud of myself, I told anyone who would listen! Thank you to all of the men and women who took the time to detail what to do, you made my first repair as a single mom awesome!!

I checked prices on the internet and found your price the cheapest and ordered the part on a holiday. The part arrived in two days and was installed and back to work pronto. Having worked in sales at Caterpillar Inc for a lifetime, I know how important quick delivery and short downtime is to our customers and you came through for me. I am satisfied with my experience dealing with your company.

Easy

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

My baking element burned out after being exposed to grease and other remnants of past feasts. After some research the repair seemed straight forward so I figured I'd give it a shot. Overall it's fairly simple, though there are some things to watch out for.

I didn't remove my oven's door, which restricted my movement somewhat. After removing the bolts I was able to easily remove the old heating element and expose the two connecting wires. One wire had much more slack than the other. I connected the wire with more slack first. However, I'm somewhat uncoordinated and doing so caused the other wire to retract within the unit. I had to pull out my stove and remove the back panel, which was easy. The retracted wire was easy to find, but there was no slack available through the back access either. I actually had to unscrew the wire from the thing that is connected to the wire that plugs in to the outlet first. Doing so gave me enough slack to connect the heating element to the second wire. After that I just reconnected the wire to the outlet connection and put the back panel back on!

About 45 minutes in total time. Most of which was figuring out the approach to getting enough slack to connect the second wire and working around the oven door which restricted my movement.