J35002 General Electric Range - Instructions

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

the replacement items fit really good. It was a matter of remove and replace,

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

Ordered new burner and drip pan. New parts arrived within 3 days. Removed screw holding the hinge, removed clips from porcelain insulator, removed old burner, then installed new burner, reinstalled tilt lock hinge, replaced drip pan and ring and set burner in place. The whole installation took less than 10 minutes, and it works perfectly.

Unplugged bad surface element and plugged in replacement.

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

lift eye slide in bowl and trim ring, put the eye back down,

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

Followed the enclosed instructions

1. Turn off power to range and remove element.
2. Remove clips from ceramic guards.
3. Disconnect wiring.
4. Connect wires to new element.
5. Install ceramic guards and clips
6. Attached element to range.
7. Restore power.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.