JKP60G401 General Electric Range - Instructions

You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi

Removed the two screws that held the element in place. This required the use of a socket wrench. Removed the screws that were attached to the lead wires. The screws were of the sheet metal type.
Once the new element was in place I did have some difficulty attaching the screws to the lead wires. The reason for this was because the screws that came with the new element were threaded and I had a hard time getting the screws started because of the small size and the limited amount of slack from the lead wires. A magnetic screw driver would have made the job much easier.

Removed the two screws holding the mount and then reattached the two wires to the element.

I got the help for the install from the help desk. It went EXACTLY as described, I'm so impressed. So got the best price and the best help and we're fixed and I'm baking again. Awesome

It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.

Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

Took the old one out and replaced with the new one. It was just awkward to get at.

Shut power off to oven. Removed old element with socket wrench. Replaced old with new element, using socket wrench and new screws. restored power. That's it. Fortunately, old screws were not rusted. If they had been, would have used a rust solven.

On thanksgiving day, as we were pre-heating the oven, electric sizzle, sparks and a little flame comes from our 24 year old oven. We were able to get dinner on the table and that evening I went looking for what I thought was going to be a difficult to find part. But I found the part on partselect. I ordered that evening and got it on saturday. Installation was a snap. The most difficult part was the nuts holding the wires were stuck on from time and heat and I worried about the wire from the small plate to the coil might break. A little wd-40 and a few minutes and they popped right off and right back on. Works great now.

Easy! Removed the screws, took out the damaged element, reversed the process with the the new element. I called in my order on Monday and Wednesday evening the oven was repaired! It doesn't get any better than that. Thanks for the great service.

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.

Turn off circuit breaker. Release bake element from back of oven with a phillips head screwdriver. Remove bake element from heating wires with an adjustable wrench. 1/4 nutdriver was a little to big large for the old screw. Do not allow wires to fall back into the installation. Reverse the procedures for installing the new bake element. Most difficult part of the repair is having old eyes and not being able to focus on the work site which is about 12- 14 inches from your eyes. Young people with good eyes no problem. Oven heats like a new unit.

having read instructions from previous PartSelect users it was a snap. Nutdriveer, and screw driver were the only tools needed. This was a wall oven and the most difficulty I had was getting to the nuts with the door open. I really didn't want to take off the door.