JMC27G1J5 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from MANHATTAN, KS
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Bake element began to spark and short out when I tried to use it.
When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Boulder Creek, CA
- Parts Used:
- WB30X359
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Replacement of broken element
Read and follow the instructions. Be careful when stripping old wires to attach to new element. Fit the element to ceramic casing prior to attaching wires. If new element does not seem level after replacement heat a large pot of water. The element will expand and the weight of the pan of water will settle the element. "Physics 101"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Lititz, PA
- Parts Used:
- WB44X5082, WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake Element was bad and Drip bowls needed replaced
First I turned the breaker off the Range. Second I removed the two screws that held the element inplace. Then I pulled element front until I could get to the two screw which connected the wires and removed then. Removed old Bake element. Installed new element by connecting the two wires and then pushed the element into place and secured it by reinstalling the two screws. Turned the breaker back on and tested. This is a very easy item to replace and takes very little time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Westport, IN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
element burned out
Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pompano Beach, FL
- Parts Used:
- WB44X5082, WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Broken element / light assembly
Piece of cake
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hanover, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven Heating element broken
Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New element came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Austin, TX
- Parts Used:
- WB32X10013, WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Guest melted a nylon cutting board on the burner
Ordered new burner and drip pan. New parts arrived within 3 days. Removed screw holding the hinge, removed clips from porcelain insulator, removed old burner, then installed new burner, reinstalled tilt lock hinge, replaced drip pan and ring and set burner in place. The whole installation took less than 10 minutes, and it works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Renton, WA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Oven lower Bake Element exploded
First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from BETHLEHEM, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The bake element burned in half.
First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Cave Creek, AZ
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Baking element no longer worked.
Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from West Union, AL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bake element burnt out
Firs I shut the power off to the range. Then I removed the bottom oven rack, then removed the two screws holding the element in place. I pulled the element out about 3 inches to pull the connecting wires off. However, when I pulled the element towards me a lost on of the connecting wires that attached to the element. I then had to pull the range away from the wall and remove the back cover panel.I then fed the new element into the wholes from the inside of the range and having the back panel removed gave me full access for reconnecting the element wires. I put the back cover panel into place , put the bottom oven rack in and that was it. I was done with the repair. I turned the power back on and everything worked fine. I would recommend removing the back cover panel prior to trying to remove the element. This will save you some time and give you full access to the wiring before attempting to remove the bake element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Littleton, CO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element shorted and broke
TURN OFF CIRCUIT BREAKER before doing anything even if oven is not turned on! If I hadn't checked voltage with tester before starting I would have made a shocking discovery.
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilee from Newburgh, IN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
The bottom oven heat element didn't work
1. Removed the old element. Had a little trouble loosening the screws. After we got them loose, everything was easy.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AMELDA from BRYANS ROAD, MD
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Element at the bottom of oven cracked
First I turned off the circuit breaker leading to the oven. Then I removed the two screws that held the old element in place. I pulled out the element and disconnected the wires. I reconnected the wires to the new element and pushed it back in place. I then secured it with the two screws. I turned the circuit breaker back on and turned on the oven. Works just great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Durham, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Element either shorted or burned out.
Removed two socket head screws form inside oven rear wall. Pulled element out and disconnected two screws attaching wiring. Replaced with new.
Was this instruction helpful to you?
Thank you for voting!