JKP40G1K4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- robert from emden, MO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom unit in oven was burnt out
removed 4 screws and exchanged units put the 4 screws back in. about 10 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Danbury, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Took the element out and put the new element in place. Used the original screws - not the ones came with new element - to secure the new element back in place. DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Grapevine, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element burn out
removed and replaced element as required.thank to your website i was able to order the right part.now i have your site marked as favorite.thanks for making this easy for the non professional.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan from North White Plains, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken oven element
I removed the two screws that keep the element in place.Then I pull the element a little bit and disconnected the two wires and removed the old element. Then I reconnected the two wires on the new element then put the element back on position and put back the two screws that keep the element in place. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOE from WESTON, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned Out Lower Heating Element
Unscrewed the old one and screwed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baldwin, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned heating element (no continuity)
Removed old part, install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Meridian, MS
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
240 Volt Bake Element Failed In Upper Oven
Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Silver Spring, MD
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
My 20+ year old bake element cracked
I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Roseville, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace baking element
Turned off power at breaker and removed old element and replaced new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from kersey, PA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven element burned out
removed the element with 2 screws. disconected element with 2 screws. reversed order to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Litchfield Park, AZ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element would no longer heat up.
Shopped online for a good price for the heating element. Thw element came very quickly, very good packaging. Removed and replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Sugar Land, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes
Reversed the process to install the new coil.
Done in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from two rivers, WI
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
oven wouldn't heat eliment was burnt and sparking
took out old then put in knew
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Stone Mountain, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower heat element died in our 30+ yr old oven
IT was fast and easy! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from West Springfield, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burned out bake element
The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.
Was this instruction helpful to you?
Thank you for voting!