JBP36G4W4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ella from Tampa, FL
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pre 1992 6" plug in electric cooking elements- rusted out
Worked, don't have to replace an old GE combination range "Microwave Cooking Center" when the surface units rusted out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- STEVEN from HERNDON, VA
- Parts Used:
- WB2X3138
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Oven door gasket hard, noot sealing
I thought it would be a simple matter of removing the inside glass (4 screws) and replacing the gasket, but it turns out that on this model I had to start on the outside, remove the drawer, then remove the front door cover, then undo a screw which held the inside two-tier glass in place, THEN I could remove the four screws and the interior panel which holds the gasket in place. THIS IS A TWO PERSON JOB unless you choose to use masking tape to hold the exterior door cover in place while removing/replacing the many screws which hold it on. WHILE REPLACING THE INTERIOR COVER WHICH HOLDS THE GASKET IN PLACE, YOU MUST PERIODICALLY STRETCH IT HERE AND THERE TO GET THE "SNAKE" TO EXTEND THE ENTIRE WAY AND TO SEAL TIGHTLY.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from San Francisco, CA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner needed replacing
Just plugged it in! Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Pagosa Springs, CO
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had burned out-needed replacement
Plugged it in. It fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from New smyrna beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Baden, PA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Cortlandt Manor, NY
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not keep heat
pulled out the old one pushed in the new one
Was this instruction helpful to you?
Thank you for voting!
Dirty and stained Pans and ring
Just pulled out the three burners and lifted the pans. Lifted out the ring. Pivoted up the 3-way burner, and lifted up the pan with wider slit. Put new ones in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Littleton, MA
- Parts Used:
- WB30X219
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element failed
lift up to 45 degree angle and pull towards you. This one went bad and the contacts welded themselves together. Took some shifting and tugging to free it. Normally, they slide in and out effortlessly, like any plug.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Corpus Christi, TX
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing burner element
I bought the replacement element for my 98-year-old aunt, and she installed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert R from Richmond, MO
- Parts Used:
- WB30X218
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a burned out calrod unit
Simply unplugged the burned out one and plugged in the new one. It worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!